Assessments - 3, GPA: 4.3
(
)
)
|
Facilidade de uso
3 LOCATION OF CONTROLS LOCATION OF CONTROLS MAIN UNIT 1. Turntable 16. Play / Pause Button 2. 45 RPM Adaptor 17. Record Button 3. Cue-lever (use this lever to lift the tone arm). 18. Skip + Button 4. Tone Arm 19. Skip - Button 5. Speed Selector 20. SD/MMC Card Slot 6. Tone Arm Holder 21. Headphone Jack 7. Speaker 22. USB Port 8. Dust Cover 23. Volume Control 9. Display 24. IR Sensor 10. Tuning Control 25. Power Indicator 11. Band Selector 26. FM Antenna 12. Function Selector 27. Auto Stop (ON/OFF) Selector 13. Bass Boost Button 28. Audio LINE OUT Jacks 14. Mode Button 29. Internal Speaker (ON / OFF) Selector 15. Stop/USB/Card Button 30. AC Power Cord 4 REMOTE CONTROL UNIT 1. PLAY/PAUSE BUTTON 2. RECORD BUTTON 3. STOP/CD/USB/SD BUTTON 4. SKIP-BUTTON 5. SKIP+ BUTTON 6. DISPLAY BUTTON 7. PROG BUTTON 8. MODE BUTTON 9. FOLDER UP BUTTON 10. FOLDER DOWN BUTTON 11. DELETE BUTTON IMPORTANT NOTES Avoid installing the unit in locations described below: • Places exposed to direct sunlight or close to heat radiating appliances such as electric heaters. • Dusty, humid or moist places. • Places subject to constant vibration. POWER SOURCE This Unit is designed to only operate on normal 120V~ 60Hz household power. Do not attempt to operate the System using any other power source. You could cause damage to the unit and void your warranty. The remote control unit operates on 1 CR2025 Lithium battery (Included). AC OPERATION 1. Plug the AC POWER CORD into a 120V AC ~ 60Hz outlet. 2. Turn the System on by sliding the Function Selector (12) to either “TUNER”, “USB/SD” or “PHONO”. The LCD backlight will turn on. Remarks: If there is a malfunction due to electrostatic discharge (ESD), reset the unit by unplugging the AC CORD from the outlet, wait 30 seconds and then plug the AC CORD in again to reset to normal operation. ACTIVATING THE REMOTE CONTROL Remove the plastic insulator tag sticking out of the Battery Compartment of the Remote Control by pulling on it. Once the tag is removed, the Remote Control will be ready for use. 5 BATTERY CARE i. If the unit is not to be used for an extended period of time, remove the battery. An old or leaking battery can cause damage to the Remote Control. ii. Do not dispose of batteries in fire, batteries may explode or leak. BATTERY REPLACEMENT When the battery becomes weak, the operating distance of the Remote Control is greatly reduced and you will need to replace the Lithium battery. 1. Remove the battery compartment from bottom of the Remote Control. 2. Install 1 “CR2025” Lithium battery with the positive side facing up. 3. Replace the battery compartment. IMPORTANT: Be sure that the battery is installed correctly. Wrong polarity may damage the Remote Control and void the warranty. USING THE REMOTE CONTROL CORRECTLY Note: The Remote Control is only for operating the USB and MMC Card functions. • Point the Remote Control at the SENSOR (IR) located on the front of the System. • The functions of the remote buttons are the same as the corresponding controls on the main unit. • The performance of the infrared SENSOR may be degraded causing unreliable operation if there is a strong ambient light source in the same room. • The recommended effective distance for remote operation is about 10-15 feet. RADIO OPERATION 1. Slide the FUNCTION Selector (12) to the “TUNER” position. 2. Slide the BAND Selector (11) to either AM, FM or FM ST (FM Stereo Mode). 3. Rotate the TUNING CONTROL (10) until you reach the radio station you wish to listen to. The radio station frequency shows on the LCD DISPLAY. 4. Adjust the sound level by rotating the VOLUME CONTROL (23). 5. To turn off the radio, Slide the FUNCTION Selector (12) to the “OFF” position. The LCD DISPLAY will go “off”. FM STEREO RECEPTION With the BAND Selector (11) in the “FM ST” position, the FM Stereo Indicator “ ” will light up when listening to a strong station that is broadcasting in “Stereo”. Slide the BAND Selector (11) to the FM position if the FM stereo reception is weak. The reception may improve, but the sound is now monaural (MONO). 6 TIPS FOR BEST RECEPTION AM – The AM antenna is located inside the cabinet of the main unit. If AM reception is weak, change the position of cabinet until the internal antenna picks up the strongest AM signal. FM – During FM reception, always keep the FM Wire Antenna fully extended. If FM reception is weak try repositioning the FM Wire Antenna until you find the strongest FM signal. BASS BOOST OPERATION To enhance the low frequency sound, press the BASS BOOST BUTTON (13) once (button in) to activate. Press the BASS BOOST Button (13) again (button out) to turn the Bass Boost off. Note : Please refer to the ON/OFF graphic on the Front Panel for correct operation of the Bass Boost function. PLAYING PHONO RECORDS 1. Raise the Turntable Dust Cover. 2. Remove the stylus protector and release the Tone Arm Clamp (6). 3. Slide the Function Selector (12) to “PHONO”. 4. Place a record on the turntable, over the center spin...