Assessments - 1, GPA: 3
(
)
)
|
Fotos e especificações Gemini TT-1000 |
Facilidade de uso
NOTA: TT-1100USB mostrado. Ambos modelos tienen las mismas caracteristicas excepto el TT-1000 tiene una salida USB y un pre-amplificador de nivel de linea adicionales. NOTE: Modele presente TT-1100 USB. Les deux appareils possedent les memes caracteristiques a l’exception de la platine TT-1100 USB qui comprend une sortie USB, ainsi qu’un niveau de sortie ligne. WICHTIG: Die PLATTENSPIELER der TT-Serie verfu.gen u.ber die gleichen Standardfeatures. Der auf dieser Seite abgebildete TT-1100USB unterscheidet sich vom TT-1000 nur durch seine Leistung. Die einzige Ausnahme ist die fehlende USB Audio Ausgang und PHONO/LINE SCHALTER des TT-1000. 5 5 7 12 17 2 18 3 4 PANEL SUPERIOR FACE SUPERIEURE OBEN PANEL TRASERO FACE ARRIERE HINTEN 14 1 9 10 8 14 13 6 11 15 16 Congratulations on purchasing the Gemini TT-1000/TT-1100USB high torqe belt driven turntable. This unit is backed by a 1 year warranty*. Prior to use, we suggest that you carefully read all the instructions. TT-1000/TT-1100USB - Fully manual belt drive turntable - Battle and club style design - +/-10% Variable pitch slider - Solid aluminum platter - Fully adjustable counter weight & anti-skating controls - 33, 45 and 78 RPM, reverse playback capability - Dual soft touch start/stop buttons - Motor Off button for slower braking - Removable target light (not included) - Headshell and 45 adapter included - CN-15 cartridge & felt slipmat included - Detachable RCA & ground cables TT-1100USB - USB computer connectivity for PC and Mac - Audacity recording software included - Line level RCA outputs (with built–in pre–amp) INTRODUCTION: 4 FEATURES: CONNECTIONS: 1 MAIN POWER RECEPTACLE: Connect the detachable linecord (included in the box with your TT-1000/TT-1100USB) to the power receptacle, and plug the other end of the linecord into an AC outlet. The TT-1000/TT-1100USB has a universal power supply that can accept any AC voltage from 100 VAC to 240 VAC. No need for voltage select switches. It will work virtually anywhere in the world. It is less susceptable to voltage sags or spikes than conventional power supplies, providing greater electro magnetic isolation and better protection against AC line noise GROUNDING SCREW: You will need to ground the RCA cable(s) by screwing in the grounding fork(s) to the GROUNDING SCREW located on the rear panel of the mixer. PHONO RCA OUTPUTS: This set of outputs carries the audio signal from the turntable portion of the unit and should be connected to an appropriate phono-level input on your audio mixer. ALSO SEE ADDITIONAL TT-1100USB INFO SECTION BELOW. 2 3 TT-1000/TT-1100USB ASSEMBLY & SETUP: MOTOR DRIVE BELT 1. Start by placing the rubber DRIVE BELT around the inner bottom ring of the turntable PLATTER. This should come preinstalled, but check to make sure that it is not twisted or damaged. 2. Install the PLATTER on the center spindle and press it down firmly. Check to make sure that it rotates uniformly and does not wobble excessively. 3. Rotate the PLATTER so that one of the holes is aligned with the Start Stop button on the front corner of the turntable. The brass motor spindle should be visible through this hole. 4. Reach into the hole and pull the rubber DRIVE BELT off of the inner ring, and install it over the motor spindle. Be careful not to twist the rubber DRIVE BELT during this step. Check to make sure the PLATTER rotates uniformly. If the DRIVE BELT is properly installed, there should be a slight amount of tension that brings the PLATTER to a stop after spinning it freely. TURNTABLE INSTALLATION: 1. Make sure you have placed the platter securely on the spindle and made sure that the MOTOR DRIVE BELT is in place. 2. Put the SLIPMAT on the PLATTER. 3. Set the TURNTABLE BASE on a flat, level surface free of vibration. Use the turntable feet to stabilize the unit horizontally. 4. Try to place the unit as far away from the speakers as possible. 5. Keep the unit away from direct exposure to the sun, heat, moisture or dirt. 6. Keep the unit well ventilated. HEADSHELL INSTALLATION: Insert the HEADSHELL into the front of the tubular TONE ARM. While holding the HEADSHELL firmly in a horizontal position, turn the LOCKING NUT counter clockwise until the HEADSHELL is locked in place. Be sure not to over tighten the LOCKING NUT. COUNTERWEIGHT INSTALLATION: 1. Slide the COUNTERWEIGHT onto the rear of the TONE ARM with the numbered stylus gauge facing forward. 2. Twist the COUNTERWEIGHT counter clockwise lightly, to screw it onto the rear of the TONE ARM. ADJUSTING HORIZONTAL ZERO BALANCE AND STYLUS PRESSURE: 1. Without touching the stylus tip, remove the stylus protector (if your cartridge has a detachable one. 2. Release the ARM CLAMP and lift the TONE ARM off the ARM REST. 3. Counter clockwise advancement of the COUNTERWEIGHT will cause the cartridge side of the TONE ARM to be lowered, turning it clockwise will cause the opposite. Turn the COUNTERWEIGHT clockwise or counter clockwise as needed until the TONE ARM is balanced horiz...
Este manual também é adequado para os modelos :Stereo - TT-1100 USB (1.24 mb)