Assessments - 4, GPA: 3.8
(
)
)
|
Facilidade de uso
To cancel Press [SURROUND] again to clear “ ” indicator. • Surround sound isheadphones. less discernible when listening through • If interference in FM stereo reception increases, cancel the surround sound effect. External unit Connecting external unitConnecting external unit Preparation • Make sure that the power supply for all components has been turned off before making any connections. • For details, refer to the operating instructions of the unit which is to be connected. • All peripheral components and cables sold separately. Connecting analog equipmentConnecting analog equipment This example shows how to connect an analog player with a PHONO OUT/LINE OUT switch. When units other than those described are to be connected, please consult your dealer. (L) AUX R L (R) “LINE OUT” position Analog player (not included) Rear panel of this unit • An analog player with a built-in phono equalizer can be connected. • Set the switch to the “LINE OUT” position at the back of the analog player. Playing or recording from an externalPlaying or recording from an external unitunit Press [AUX]. 1 For listening: Proceed to step 3. 2 For recording: Press [¶REC/8] to start recording. Start playback from the external source. (For details, 3 refer to the external unit’s instruction manual.) 16 RQT8038 Troubleshooting guide Troubleshooting guide Before requesting service, make the following checks. If you are in doubt about some of the check points, or if the remedies indicated in the chart do not solve the problem, refer to the “Customer Services Directory” on page 18 if you reside in the U.S.A., or refer to the “Product information” on page 19 if you reside in Canada. Common problems No sound. Turn the volume up. The speaker cords may not be connected properly. Turn the unit off, check and correct the connections and turn the unit on (refer page 4). Sound is unfixed, reversed or comes from one speaker only. Check the speaker connections (refer page 4). Humming heard during play. An AC power supply cord or fluorescent light is near the cables. Keep other appliances and cords away from this unit’s cables. “ERROR” is displayed. Incorrect operation performed. Read the instructions and try again. “– –:– –” appears on the display. You plugged the AC power supply cord in for the first time or there was a power failure recently. Set the time (refer page 14). “F61” is displayed. Check and correct the speaker cord connections (refer page 4). If this does not fix the problem, there is a power supply problem. Consult the dealer. Listening to the radio Noise is heard. Use an outdoor antenna (refer page 4). The stereo indicator fl ickers or doesn’t light. Sound is distorted. A beat sound is heard. Turn the TV off or separate it from the unit. A low hum is heard during AM Separate the antenna from other cables and cords. broadcast. When there is a television set nearby The picture on the TV disappears or The location and orientation of the antenna are incorrect. If you are using an indoor antenna, stripes appear on the screen. change to an outdoor antenna (refer page 4). The TV antenna wire is too close to the unit. Separate the antenna wire of the TV set from the unit. Using the cassette deck Recording is not possible. If the erasure prevention tabs have been removed, cover the holes with adhesive tape (refer page 12). Playing discs The display is wrong or play won’t The disc may be upside down (refer page 7). start. Wipe the disc. Replace the disc if it is scratched, warped, or non-standard. Condensation may have formed inside the unit due to a sudden change in temperature. Wait about an hour for it to clear and try again. The total number of tracks displayed The disc may be scratched, or its data may be defective. Replace the disc. differs each time the same disc is inserted. Unusual sound is heard. CD-RW cannot be read. The disc was incompletely formatted. Use the recording equipment to fully format the disc before recording. “VBR–” is displayed instead of the The unit cannot display the remaining play time for variable bit rate (VBR) tracks. remaining play time. “TAKE OUT/DISC” appears on the There is a problem with the disc mechanism. (A power failure may have occurred.) display. The tray will open automatically. Remove the disc from the tray, and after ensuring there is no disc in the tray, close it. The unit will make the disc changing noises for a few moments and then it should operate normally. The remote control Remote control doesn’t work. Check that the batteries are inserted correctly (refer page 5). Replace the batteries if they are worn. 17 RQT8038 Warranty (ONLY FOR U.S.A.) Warranty (ONLY FOR U.S.A.) Panasonic Consumer Electronics Company, Panasonic Puerto Rico, Inc. Division of Panasonic Corporation of North America Ave. 65 de Infanteria, Km. 9.5 One Panasonic Way Secaucus, New Jersey 07094 San Gabriel Industrial Park, Carolina, Puerto Rico 00985 Panasonic Audio Products Limited Warranty Limited Warranty Coverage If your ...