Assessments - 3, GPA: 3.3 ( )

Fabricante : Panasonic Arquivo Tamanho: 3.78 mb Arquivo Nome : SCAK75.PDF Língua de Ensino:

(See “Presetting only your favorite stations” below.) Q Press TUNER BAND to select the band. The power will come on automatically. Every time you press the button; “FM”<—>“AM”. Ul Press TUNE MODE to select “MANUAL”. Every time you press the button; “MANUAL”«—> “PRESET”. 0 Press v or a until the display shows the frequency from which you want to begin automatic memory presetting. Tips on tuning in radio stations © Hold down either arrow button until the frequency numbers start scrolling. Continue to hold the button. (2) When near to the frequency you are looking for, press the button repeatedly until the station is tuned in. □ Press and hold MEMORY until the frequency begins to change. This will start presetting automatically. When finished, the radio will tune in the last station memorized. If auto presetting is not possible because radio signals are weak or for some other reason, do the following. Presetting only your favorite stations Preset the stations one at a time. 1. Perform step 1 above. Then, press MEMORY ("MEMO” flashes) and select a station with v and a . 2. While “MEMO” is flashing press MEMORY again and select a preset channel with v or a. 3. Press MEMORY to preset the station. Memory retention The memory can retain presetting for up to two weeks after being disconnected from the power source. FM allocation settings: The FM frequency step is set to 0.2 MHz at the time of shipment. By adjusting the allocation as shown below, you can enable the system to receive FM broadcasts allocated in 0.1 MHz steps. 1. Press and hold TUNER BAND for approximately 5 seconds. The frequency display will be returned to the minimum frequency of the FM band and the display will begin to flash. Keep holding for approximately 5 more seconds. 2. When the display stops flashing and indicates a different frequency number (the frequency step is changed to 0.1 MHz.), release TUNER BAND. To return to the original frequency, repeat steps 1 to 2 above. After changing the “allocation" setting, the frequencies you previously preset in the memory will be cleared. ■i i Íj. % Sí » 4: * 4 *• I * * * ‘ i** *•*' 11 * f * * ? ® ■* * . » » * *. * T **■■*.* ■**■*■* SM4 4 * *. , V4- ».*.*.♦ * * 4 * it ( «í -'4- :» * :®- * * * * *. i . *. 4 í * * * * * * , i » *,■ * f » *■ # « * * % * » *. * * í . i # i i *■ t .* * > .* * * > * ;*. * } * % *' i: * * .¿.. * -* » * > ? t: * i; * * * * * * 1 * :* * * í ** *• * * * •* * * * ■:« * .*. % •*.. * * * t * * z i* *• * •*. S .«■■ * * * „ :W •» * i- * S * * „ * * V- 4 ••* f .* 5 í !Íf*!fR..,_ , i ■ » i i: * * * * É'-Ü- *"• * s::i # #; ||| | (► <• * "P * n Press TUNER BAND to select band. The power will come on automatically. Every time you press the button; “FM”«—>“AM”. U\ Press TUNE MODE to select “PRESET” or “MANUAL”. Every time you press the button; “MANUAL”«—»"PRESET”. PRESET: For preset stations MANUAL: For non-preset stations B Press v or a to select the desired broadcast. "STEREO” iights when an FM stereo broadcast is being received. “TUNED” lights when you precisely tune in a station. □ Adjust the volume level. Auto tuning Auto tuning is an easy way to tune in non-preset stations in the manual mode. Hold down either v or a , and release the button when the frequency starts scrolling. The radio will stop automatically on the first station it picks up. •When there is outside interference, the radio sometimes stops on a certain frequency where no station is broadcasting. To stop auto tuning Press either v or a again. If noise is excessive in the FM stereo mode Q Press FM MODE/BP. (“MONO” will light up.) Sound will be produced in monaural, but this also reduces noise. Press the button again to cancel. “MONO” will go out. Normally, you’ll want to listen in stereo, so leave “MONO” off. This way, you can listen to stereo broadcasts in stereo, and monaural broadcasts in mono. You can preset an FM station in monaural by following the steps under “Presetting only your favorite stations” page 12). After selecting the station in step 1, select “MONO” with FM MODE/BP, then continue with steps 2 and 3. • If you preset stations in memory, you can tune in a preset station by simply selecting the preset channel with the numeric buttons on the remote control. 1. Press TUNER on the remote control. 2. Press the numeric button{s) to select the desired preset channel. To select a two-digit channel: Press >10 and then the two numbers you want within 10 seconds or so. • Sound is momentarily interrupted if you load/unload tapes while listening to an AM broadcast. Radio operations You can set and remove CDs while a CD is playing. How to remove CDs How to set CDs 1. Open the rack panel. идя Except when setting or removing CDs, keep hands out of the changer while open. You couid injure yourself if somehow entangled in the internal mechanism. 2. Slide the loader carriage to the slot you want шт The load...

Baixe o seu

Para fazer o download, introduza 2 dígitos :