Assessments - 2, GPA: 4
(
)
)
|
Facilidade de uso
(“Reverse function" ^ page 34.) I Listening □ Listening to cassette tapes Deck 1 Tape side indicator | Peck 2 | Tape side indicator m Press [DECK 1/2] to select the Deck (1 or 2). Press [ 44 ] or [ ►► ]. Because this unit is capable of playing back both sides of the tape, the operation changes in accordance with the direction of the tape side indicator. The tapes in Deck 1 and Deck 2 can be advanced or rewound at the same time, if DECK 1/2 The tape counter indicates the amount of tape travel as a numerical value based on the number of revolutions of the tape hub. As you switch between Deck 1 and Deck 2, the tape counter shown on the display changes too. To reset the tope counter Press [COUNTER RESET]. The tape counter of the currently selected deck will revert back to “000”, while that of the other deck will remain unchanged. For your reference: When the tape is traveling in the reverse direction, the value displayed on the tape counter will count down. After “000" is reached, the display will switch to “999” and will then continue counting down. COUNTER RESET о -1 COUNTER DIGITAL INPUT INPUT SELECTOR PHONES BASS TREBLE BALANCE VOLUME MUTING o- ODD P O Ö ÇÔÔÛ ET BASS TREBLE (©} (®) BALANCE (®) 0 MUTING t\/ll I I I l\ I! II I II I i I I \lf 1 I I a INPUT SELECTOR O u VOLUME Other functions El Turn [BASS] to adjust the low frequency sound. Turn [TREBLE] to adjust the high frequency sound. m Turn [BALANCE] to adjust the left/right sound balance. Ife (ïïIïijS(Î^ ' .«f E by remote control only Press [MUTING]. The message “MUTING ON NOW” runs repeatedly from right to left across the display as long as the muting function is on. Press once again to return to the previous volume level. E339 Muting is cancelled when the receiver is turned off. sources Turn [INPUT SELECTOR] to select and start the desired source. {Refer to the appropriate operating instructions for details.) The indicator corresponding the select source lights and the source is shown on the display. VCR : To watch video tapes TV: To watch TV DVD : To watch DVD PHONO: To listen to phono discs IJBfll To watch a video (or DVD) or the TV, set the TV to either, the TV mode or VIDEO mode. If you are using VCR and you select TAPE, CD, TUNER, or PHONO The picture will remain on the screen. Press [DIGITAL INPUT] to select “DIGITAL” if you have used digital connection for TV, DVD, or CD. The DIGITAL INPUT indicator lights. Only Dolby Digital, DTS or PCM signals (44.1 kHz or 48 kHz) can be reproduced through the digital terminal: The digital input signal of sampling frequencies 96 kHz and other signal formats such as MPEG cannot be reproduced on the receiver. ‘¡fct fffcfcm (flpsirEfo IWr%fiT?iTreR CD Reduce the volume. ©Connect the headphones. • Plug type: 6.3 mm (1/4 in.) stereo (3) Adjust the volume. Select STEREO or turn SPEAKERS A and B off when using headphones. Turning the speakers off automatically engages STEREO mode and ensures no sound is heard from the subwoofer. If SURROUND is used, the sound heard through the headphones will seem unusual. Avoid listening for prolonged periods of time to prevent hearing damage. Other functions A, В SFC MODE SUBWOOFER TAPE TAPE MONITOR (MONITOR) ЕГ TAPE MONITOR CD A SPEAKERS В A SPEAKERS В (D © SFC MODE Ю) A SPEAKERS В IB' SUBWOOFER (MONITOR) (tafeia? i: □ This indicator lights in the following two situations: 1. While TAPE is selected. 2. While TAPE MONITOR is in use. To use the tape monitor The tape monitor can be used to check the recorded sound when connecting a 3 head tape deck (not included) or using the graphic equalizer. If [TAPE MONITOR] is pressed while a source other than TAPE is selected, the "TAPE (MONITOR)" indicator lights and the tape monitor comes on. Press [TAPE MONITOR] again to turn the tape monitor off. • The tape monitor cannot be used when TV, DVD, or CD digital input is being used. • If you are using the tape monitor and you select a digital input source, the tape monitor switches off. • Depending on the setting on the graphic equalizer, there may be some distortion pages 46). m “Dynamic range compression” (DR COMP) is a function for compressing the dynamic range (reproduction level range) of audio signals. It is used for viewing movie software late at night or at other times when high volume levels are not desirable. This function only works with DR COMP compatible Dolby Digital format software. The factory setting is “OFF’. © Press [A] and [B] at the same time. “SETTING" appears on the display. CD Press [A] to select “DR COMP”. Each time the button is pressed the display switches as follows. SIZE —- DISTANCE —- FILTER —- DR COMP t_I (3) Turn [SFC MODE] to select the setting. Each time the selector is turned the display switches as follows. OFF—- STANDARD —- MAX t_I The factory setting is “OFF”. (4) Press [A] and [B]. “COMPLETE” appears on the display. For your referenc...