Assessments - 2, GPA: 4
(
)
)
|
Facilidade de uso
In this case, use the DSP system instead. DOLBY SURROUND P R O L O G I C PRO-Logic 3 STEREO OFF Adjusting Speaker Level Balance The unit is equipped with a built-in test signal generator called a noise sequencer which outputs a noise signal that ‘travels’ from channel to channel. This enables the simple adjustment of sound levels, to achieve, at the listening position, the same apparent loudness from each channel. Use the remote control. Press the Dolby Surround button. Result: “ PRO-LOGIC” appears on the displayed. Press the Test Tone button. A noise signal is sent to each channel in turn in the following sequence. (L : Left Speaker, CNTR : Center Speaker, R : Right Speaker, REAR : Rear Speaker) Press the Test Tone button again to stop the noise signal. To change the sound levels or delay time after adjusting the balance with the noise sequencer. Press the Sound Edit button. While L, R, CNTR, REAR is displayed, press the UP/DOWN ( / ) button. Press the Speaker Mode button. While CNTR, REAR, DELAY TIME is displayed, press the UP/DOWN ( / ) button. – CNTR : Large/Small/None – REAR : USE/None – DELAY TIME : 15/20/25/30 MS When the Dolby surround system is on, this function can be operated. 1 2 3 4 L CNTR R REAR Dolby Surround 4 4 4 1 2,3 4 4 GB 24 25 You can improve the quality of radio reception by: Rotating the FM or AM(MW) aerial Testing the positions of the FM and AM(MW) aerials before fixing them permanently If reception from a specific FM radio station is poor, press Mono/ST. to switch from stereo mode to mono. The quality of the sound will be improved. Improving Radio Reception You can listen to a stored radio station as follows: Switch the system on by pressing On/Standby. Select the TUNER function by pressing Band on remote control. Select the required frequency band by pressing Band on the remote control or TUNER (Band) again on the front panel. Press the Tuning Mode button on the front panel of the unit, or the Tuning Mode button on the remote control until “PRESET” is displayed. Tuning the Multi-Jog on the front panel left or right until the desired station is found. or Select the desired station by pressing the station number stored, using the Tuning or button on the remote control. Result: The desired station is now received. Selecting a Stored Station 1 2 3 4 5 1 5 You can store up to: 15 FM stations 15 AM stations (option) 15 FM stations 8 MW stations (option) 7 LW stations 15 FM stations 5 MW stations 5 SW1 stations (option) 5 SW2 stations Switch the system on by pressing On/Standby. Select the TUNER function by pressing TUNER on the front panel. Select the required frequency band by pressing TUNER (Band) again on the front panel or Tuner (Band) on the remote control. Result: The appropriate indication is displayed: FM Frequency Modulation AM(MW) Medium Wave LW(OPTION) Long Wave SW1, SW2(OPTION) Short Wave To search for a Press Tuning Mode station... Manually One or more times until MANUAL is displayed. Automatically One or more times until AUTO is displayed. Select the station to be stored by: Turning the Multi Jog knob to the right or to the left to increase or decrease the frequency respectively or Pressing Tuning or on the remote control To scroll through the frequencies faster when searching manually, hold down the Tuning Mode Down or Up buttons. The automatic search procedure may stop on a frequency that does not correspond to a radio station. If this happens, use the manual search mode. Adjust the volume by: Turning the Volume knob on the front panel or Pressing the VOL. + or – buttons on the remote control Select the stereo or mono mode by pressing Mono/ST. If you do not want to store the radio station found, revert to Step 4 and search for another station. Otherwise: a Press Memory. Result: The PRGM is displayed for a few seconds. b Press Tuning Mode Down and Up to assign a program number between 1 and 15. c Press Memory to store the radio station. Result: PRGM is no longer displayed and the station is stored. To store any other radio frequencies required, repeat Steps 3 to 8. The PROGRAM function can be used to assign a new station to an existing program number. Searching for and Storing the Radio Stations Searching for and Storing the Radio Stations 1 2 3 4 5 6 7 8 9 1 4 2,3 5,8 5,8 7 8 6 5 6 4,5 4,5 6 2,3 5 GB 27 The PTY information is composed of an identification symbol, which helps the FM radio to recognize the program type of each FM station. The 30 PTY modes are shown in the display by pressing the PTY button. About PTY-SEARCH Tuned to an FM station broadcasting a PTY MODE. See the FM receiving method on the page 10. If the received station is transmitting the RDS information, "RDS" lights up. Press the PTY button. The PTY MODE(NEWS, AFFAIRS, etc) appears on the display. Press the Tuning Down or Up button to select the desired PTY MODE. If the station is transmitting no PTY information, 'NO PTY' shows on the display. When the PTY MODE is selected(The PTY MODE is shown in the ...