Assessments - 0, GPA: 0
(
)
)
|
Facilidade de uso
A Speaker connections Use the supplied speakers only. Using other speakers can damage the set or the sound quality will be negatively affected. . Connect the cable of the left speaker to LEFT (red and black) and the cable of the right speaker to RIGHT (red and black) as follows: a. Press the clip of the red terminal and fully inser t the stripped por tion of the colored (or marked) speaker cable into the socket, then release the clip b. Press the clip of the black terminal and fully inser t the stripped por tion of the black (or unmarked) speaker cable into the socket, then release the clip BAntenna connections MW antenna Connect the supplied MW loop antenna to the “AM aerial” terminal. Adjust the position of the antenna for optimal reception. 12 Installation . Position the antenna as far as possible from a TV, VCR or other radiation source. FM antenna The wire antenna supplied can only be used to receive nearby stations. For better reception we recommend using a cable antenna system or an outdoor antenna. 1 Extend the wire antenna and fit it to FM ANTENNA as shown below. Note: If you are using a cable antenna system or an outdoor antenna, fit the antenna plug, instead of the wire antenna, to FM ANTENNA . 2 Move the antenna in different positions for optimal reception (as far away as possible from the TV,VCR or other radiation sources) 3 Fix the antenna’s end to the wall. Helpful hints: –To receive optimal radio reception, put the main unit and the antennas as far away as possible from the power adaptor. Connecting an additional appliance Connecting a USB device or memory card By connecting a USB mass storage device (including USB flash memor y, USB flash players or memory cards) to the Hi-Fi system, you can enjoy the music stored on the external device through the powerful speakers of Hi-Fi system. 1 Inser t the USB device’s USB plug into the socket on the front panel of the main set. Or, for the devices with USB cable: a. Inser t one plug of the USB cable (not supplied) to the socket on the front panel of the main set. b. Inser t the other plug of the USB cable to the USB output terminal of the USB device. Or, for the memory card: a. Insert the memor y card into a card reader (not supplied). b. Use a USB cable (not supplied) to connect the card reader to the socket . on the front panel of the main set. Connecting a non-USB device It is possible to use an additional appliance, e.g. TV,VCR or CD recorder with the set. On MCM279, you can playback music from an external source. 1 Inser t one plug of the audio cable (not supplied) to the socket AUX IN at the rear panel of the main set. 2 Connect the other end of the audio cable to the AUDIO OUT terminal of the additional appliance. 3 Select AUX mode on the set. Helpful hints: – Always refer to the owner’s manual of other equipment for complete connection. English 13 Installation English Using AC power 1 Make sure all the connections have been made before switching on the power supply. 2 Connect the supplied AC/DC power adaptor to the DC jack (located on the rear panel of the main set) and to the wall socket.This switches on the power supply. To avoid damage to the set, use only the adaptor supplied. When MCM279 is switched to standby, it is still consuming some power. To disconnect the system from the power supply completely, remove the power plug from the wall socket. The type plate is located on the rear of the set. Warning! To avoid overheating of the system, a safety circuit has been built in. Therefore, your system may switch to Standby mode automatically under extreme conditions. If this happens, let the system cool down before reusing it (not available for all versions). This product complies with the radio interference requirements of the European Community. CAUTION Visible and invisible laser radiation. If the cover is open, do not look at the beam. High voltage! Do not open.You run the risk of getting an electric shock. The machine does not contain any user- serviceable parts. Modification of the product could result in hazardous radiation of EMC or other unsafe operation. 14 Preparation Using the remote control IMPORTANT! – Remove the protective plastic tab before using the remote control. – Always point the remote control directly towards IR area on the main set. Notes for remote control: – First select the source you wish to control by pressing one of the source select keys on the remote control (for example CD, TUNER). – Then select the desired function (for example EA, i , e). To replace the remote controls’ battery (CR2025) 1 Push to open the battery tray. 2 Replace a new battery according to the indicated polarity. 3 Push the battery tray back to close it. CAUTION! – Batteries contain chemical substances, so they should be disposed of properly. Setting the clock After connecting MCM279 to the power supply, set the clock first. 1 Press and hold STANDBY-ON/ ECO POWER to switch the set to Standby mode. . The display shows the set time. . -- --:--...