Assessments - 0, GPA: 0
(
)
)
|
Facilidade de uso
CD or TUNER can be set to switch on at a preset time.The clock time needs to be set first before the timer can be used. . If no button is pressed within 90 seconds during timer setup, the system will exit timer setting mode automatically. 1 In any mode, press TIMER for more than 2 seconds. 2 Press .1 / 2™ (CD / TUNER or .1 / 2™ on the remote control) to select sound source. 3 Press TIMER to confirm your desired source. . The clock digits for the hours flash. 4 Press .1 / 2™ to set the hours. 5 Press TIMER again. . The clock digits for the minutes flash. 6 Press .1 / 2™ to set the minutes. 7 Press TIMER to confirm the time. . The timer is now set and actiated. Note: -If source CD is selected and no disc is in the CD tray or the disc has an error,TUNER will be selected automatically. Activating and deactivating TIMER . In standby or during playback, press TIMER once. . Display shows TIMER if activated, and disappears if deactivated. English 17 Clock/Timer English Activating and deactivating SLEEP The sleep timer enables the system to switch off by itself after a set period of time. . Press SLEEP on the remote control repeatly to select desired time before system shuts off. . Display shows SLEEP and series of time options for selection: 60, 45, 30,15, 0, 60. . To deactivate, press SLEEP on the remote control once or more until ‘0’ is shown, or press POWER / y on the system or remote control. Specifications AMPLIFIER Output power .......................................... 2 x 2 W RMS ................................................................. 4 W + 4 W MPO Signal-to-noise ratio .......................... . 62 dBA (IEC) Frequency response ......... 63 – 16000 Hz, ± 3 dB Impedance loudspeakers ......................................... 8 . Impedance headphones ................. 32 . – 1000 . CD PLAYER Frequency range .................................. 63 – 16000 Hz Signal-to-noise ratio ............................................ 65 dBA TUNER FM wave range ................................... 87.5 – 108 MHz MW wave range ................................ 531 – 1602 kHz TAPE DECK Frequency response Normal tape (type I) ...... 125 – 8000 Hz (8 dB) Signal-to-noise ratio Normal tape (type I) .................................... 34 dBA Wow and flutter ......................................... . 0.4% DIN SPEAKERS Bass reflex system Dimensions (w x h x d) .................................................... .................................................. 130 x 224.5 x 213 (mm) GENERAL INFORMATION AC Power ..................................... 220 – 230 V / 50 Hz Dimensions (w x h x d) ..................................................... .............................................. 168 x 224.5 x 214.5 (mm) Weight (with/without speakers) .................................. ............................................................ approx. 4.6 / 2.25 kg Standby power consumption .......................... < 3 W Subject to modification 18 Troubleshooting WARNING Under no circumstances should you try to repair the system yourself, as this will invalidate the warranty. Do not open the system as there is a risk of electric shock. If a fault occurs, first check the points listed below before taking the system for repair. If you are unable to remedy a problem by following these hints, consult your dealer or service centre. Problem Solution CD OPERATION “no cd” is displayed. – Inser t a disc. – Check if the disc is inser ted upside down. –Wait until the moisture condensation at the lens has cleared. – Replace or clean the disc, see “Maintenance”. – Use a finalised CD-RW or CD-R. RADIO RECEPTION Radio reception is poor. – If the signal is too weak, adjust the antenna or connect an external antenna for better reception. – Increase the distance between the Micro HiFi System and your TV or VCR. TAPE OPERATION / RECORDING Recording or playback cannot be made. – Clean deck par ts, see “Maintenance”. – Use only normal (IEC I) tape for recording. – Apply a piece of adhesive tape over the missing tab space. GENERAL The system does not react when buttons – Remove and reconnect the AC power plug and are pressed. switch on the system again. Sound cannot be heard or is of poor – Adjust the volume. quality. – Disconnect the headphones. – Check that the speakers are connected correctly. – Check if the stripped speaker wire is clamped. The left and right sound outputs are – Check the speaker connections and location. reversed. English 19 Troubleshooting English The remote control does not function – Select the source (CD or TUNER, for example) properly. before pressing the function button (E,i,e). – Reduce the distance between the remote control and the system. – Insert the batteries with their polarities (+/– signs) aligned as indicated. –Replace the batteries. –Point the remote control directly toward IR sensor on the front of the system. The timer is not working. – Set the clock correctly. – PressTIMER to switch on the timer. – If ...