Assessments - 1, GPA: 4
(
)
)
|
Facilidade de uso
Press ./. . repeatedly to set the hour, and then press ENTER .. The minute indication flashes. Use the procedure above to set the minute. 5 Use the same procedure as in step 4 to set the time to stop playing or recording. 6 Select the sound source or prepare the tape. For Play Timer: Press ./. . repeatedly until the desired sound source appears, and then press ENTER .. The display shows the timer settings. For Rec Timer: Load a recordable tape. The display shows the timer settings. 7 Press ... (power) . to turn off the system. The system turns on 15 seconds before the preset time. If the system is on at the preset time, the Play Timer and the Rec Timer will not play or record. To activate or check the timer again Press CLOCK/TIMER SELECT ., press ./. . repeatedly until “PLAY SEL” or “REC SEL” appears, and then press ENTER .. To cancel the timer Repeat the same procedure as above until “TIMER OFF” appears, and then press ENTER .. To change the setting Start over from step 1. Tips • The Play Timer setting remains as long as the setting is not canceled manually. • The volume is reduced to minimum during the Rec Timer. • The Rec Timer is canceled automatically after the Rec Timer has been activated. Troubleshooting 1 Make sure the power cord and speaker cords are correctly and firmly connected. 2 Find your problem in the checklist below, and take the indicated corrective action. If the issue persists, contact your nearest Sony dealer. If the STANDBY indicator flashes Immediately unplug the power cord, and check the following item. • If your system has a voltage selector, is the voltage selector set to the correct voltage? • Are you using only the supplied speakers? • Is anything blocking the ventilation holes on the rear of the system? After the STANDBY indicator . stops flashing, reconnect the power cord, and turn on the system. If the issue persists, contact your nearest Sony dealer. General Sound comes from one channel, or the left and right volumes are unbalanced. • Place the speakers as symmetrically as possible. • Connect only the supplied speakers. Severe hum or noise. • Move the system away from sources of noise. • Connect the system to a different wall socket. • Install a noise filter (available separately) to the power cord. The remote does not function. • Remove any obstacles between the remote and the remote sensor . on the unit, and position the unit away from fluorescent lights. • Point the remote at the system’s sensor. • Move the remote closer to the system. The STANDBY indicator . remains lit after unplugging the power cord. • The STANDBY indicator . may not turn off immediately after unplugging the power cord. This is not a malfunction. The indicator will turn off after about 40 seconds. CD/MP3 player The sound skips, or the disc will not play. • Wipe the disc clean, and replace it. • Move the system to a location away from vibration (for example, on top of a stable stand). • Move the speakers away from the system, or place them on separate stands. At high volume, speaker vibration may cause the sound to skip. Play does not start from the first track. • Return to Normal Play by pressing PLAY MODE . repeatedly until both “PGM” and “SHUF” disappear. Starting playback takes more time than usual. • The following discs take a longer time to start playback. – a disc recorded with a complicated tree structure. – a disc recorded in multisession mode. – a disc that has not been finalized (a disc to which data can be added). – a disc that has many folders. Tuner Severe hum or noise, or stations cannot be received. • Connect the antenna properly. • Find a location and an orientation that provide good reception, and then set up the antenna again. • Connect a commercially available external antenna. • Consult your nearest Sony dealer if the supplied AM antenna has come off the plastic stand. • Turn off nearby electrical equipment. Tape deck The sound exhibits excessive wow or flutter or dropout. • Clean the capstans and pinch rollers. Also, clean and demagnetize the tape heads. See “Precautions” for details. To change the AM tuning interval The AM tuning interval is factory-preset to 9 kHz (or 10 kHz, for some areas; this function is not available on the European and Russian models). Use buttons on the unit to change the AM tuning interval. 1 Tune in any AM station, and then turn off the system. 2 While holding down .. ., press ... (power) .. All the AM preset stations are erased. To reset the interval to the factory preset, repeat the procedure. You cannot change the AM tuning interval in Power Saving Mode. To improve tuner reception Turn off CD player power by using the CD power management function. By default, CD power is turned on. You cannot change the setting in Power Saving Mode. Use buttons on the unit to turn off CD player power. 1 Press CD/. (play/pause) . to select the CD function. 2 Press ... (power) . to turn off the system. 3 After “STANDBY” stops flashing, press ... (power) . while holding ....
Este manual também é adequado para os modelos :Stereo - CMT-SPZ50 (406.69 kb)
Stereo - CMT-SPZ70 (406.69 kb)