|
por este dispositivo também tem outras instruções :
Facilidade de uso
Preset number VOLUME ALL DISCS § The bands you can receive vary depending on the model you purchased. Be sure to check which bands you can receive. Every time you press this button, the band changes as follows: 2 band model: 4 Turn the jog dial to select the preset number you want. FM .AM 5 Press ENTER/NEXT. 3 band model: The station is stored. FM nMW nSW n 6 Repeat steps 1 to 5 to store other or stations. FM nMW nLW n To tune in a station with a weak 4 band model: signal FM nMW nLW nUKV* n Press + or – repeatedly in step 2 to tune in the * “STEREO PLUS” is displayed when you select UKV. 2 Press and hold + or – until the frequency indication starts to change, then release. Scanning stops when the system tunes in a station. “TUNED” and “STEREO” (for a stereo program) appear. MONO TUNED STEREO station manually. To change the preset number Start over from step 1. To change the AM tuning interval (Except for the European, Russian and Middle Eastern models) The AM tuning interval is factory set to 9 kHz (10 kHz in some areas). To change the AM tuning interval, tune in any AM station first, then turn off the power. While holding down the ENTER/NEXT button, turn the power back on. When you change the interval, AM preset stations will be erased. To reset the interval, repeat the same procedure. VOLUME Tip ALL DISCS kHz MHz § The preset stations are retained for half a day even if you unplug the power cord or if a power failure occurs. Connecting optional AV components To enhance your system, you can connect optional components. Refer to the instructions of each component. Connecting an MD deck for analog recording Make sure to match the color of the plugs and the connectors. To listen to the sound of the connected MD deck, press FUNCTION repeatedly until “MD” appears. To the audio output To the audio input of the MD deck of the MD deck Connecting audio components Select one of the following two connections, depending on the equipment to be connected and method of connecting. Connecting an MD deck for digital recording You can record from CD into the MD deck digitally by connecting an optical cable. To the DIGITAL IN jack of the MD deck Tip When you connect a Sony MD deck, you can use the MD (, P, and pbuttons on this unit’s remote to perform play, pause, and stop operations. Note If you cannot select “MD” even when you have pressed FUNCTION, press while pressing FUNCTION when the power is turned off. “VIDEO” will be switched to “MD”. To return to “VIDEO” do the same procedure. continued Connecting optional AV components (continued) Connecting a super woofer speaker (except for MHC-R700 / RX77S / RX77 (European models)) You can connect an optional super woofer speaker. To super woofer Connecting the surround speakers (MHC-RX77 (Canadian model) only) Connect the speaker cords from the surround speakers to the appropriate SURROUND SPEAKER jacks. Connect the solid cords to the red jacks and connect the striped cords to the black jacks. Keep the speaker cords away from the antennas to prevent noise. Notes • Do not place the surround speakers on top of a TV. This may cause distortion of the colors in the TV screen. • Be sure to connect both left and right surround speakers. Otherwise, the sound will not be heard. Connecting a VCR Make sure to match the color of the plugs and the connectors. To listen to the sound of the connected VCR, hold down FUNCTION and press when the power is turned off. This switches the “MD” function to “VIDEO”. Once you enable the “VIDEO” function, just press FUNCTION repeatedly until “VIDEO” appears. To the audio output of the VCR Note If the sound is distorted when selecting “VIDEO”, or you want to switch back to “MD”, repeat the operation described above for switching to “VIDEO”. To surround To surround10 speaker (R) speaker (L) Connecting outdoor antennas Connect the outdoor antenna to improve the reception. FM antenna Connect the optional FM outdoor antenna. You can also use the TV antenna instead. Jack type A AM antenna Connect a 6- to 15- meter (20- to 50- feet) insulated wire to the AM antenna terminal. Leave the supplied AM loop antenna connected. Jack type A Screw clamp Insulated wire (not supplied) FM75 AM FM75 AM y 75-ohm coaxial cable (not supplied) Screw clamp Ground wire (not supplied) Jack type B Ground wire (not supplied) Insulated wire (not supplied) Jack type B FM75 AM COAXIAL y Screw clamp FM75 AM COAXIAL IEC standard socket connector (not supplied) Screw clamp y Ground wire (not supplied) Important Ground wire (not supplied) If you connect an outdoor antenna, ground from yterminal with the screw clamp. To prevent a gas explosion, do not connect the ground wire to a gas pipe. Basic Operations Basic Operations CD (Pp Playing a CD — Normal play You can play up to three CDs in a row. 2 1(Power) 1 Press ¤and place up to two CDs on the disc tray. If a disc is not placed properly it will not be recognized. With the label side up. When you play a single CD, place it on the inner circ...
Este manual também é adequado para os modelos :Stereo - MHC-GRX7 (942.19 kb)
Stereo - MHC-GRX9000 (942.19 kb)
Stereo - MHC-R700 (942.19 kb)
Stereo - MHC-RX55 (942.19 kb)