Assessments - 5, GPA: 3.8
(
)
)
|
Facilidade de uso
This system is ideal for the bass guitarist who needs to hear all of the tones and nuances that his four-string bass is capable of producing, at high stage levels. The B-410 is suitable for full-range reproduction of conventional 4-string basses and basses with a “dropped-D" tuning (or low-D extension). This system is capable of thunderous output levels. The B-410 is perfect for the modern bassist who may be incorporating "pop” and “slap" techniques into his/her playing. The extended high-frequency response and the tight low-frequency response combine to provide exceptional clarity and punch. The sound and feel of this system also make it Ideal for use as the high-frequency section in a concert scale biamped system. The B-410 would complement any high-output, low-frequency enclosure to form a state-of-the-art biamped bass guitar system. The unusually wide frequency response of this system is achieved without the use of a tweeter and the crossover it would require. This design principle provides an inherently more reliable system. If you are used to conventional speakers, some adjustment to your amplifier’s tone controls will probably be desired. Experimentation is the key to finding the sound that you are looking for. The speakers in this system have been completely redesigned and “voiced” specifically for modern bass players. The magnet structure has been newly designed to provide both high energy and relatively light weight. The voice coil is constructed of a single layer of flat aluminum wire for light weight, low inductance and high efficiency. (Remember, light weight in a speaker's moving system and high efficiency in the magnet structure generally translate to good high-frequency and transient response.) The most visually obvious change to these speakers is in the cone and dust dome. It is a new composite material made of paper fibers with mica and epoxy added for remarkable stiffness. The end result is a speaker with a very light-weight moving system and a bright and open sound. Like most professional Electro-Voice speakers, these speakers utilize extremely rugged cast aluminum frames to ensure long-term mechanical integrity. The B-410 enclosure is made from Roadwood™ —a structural material made of layered and selectively oriented hardwood strands. Roadwood is dimensionally stable, water resistant and free from voids. All panel joints are dado cut to ensure that your speaker system sounds just as good after the tour as before. The covering is densely woven, abuse-resistant, black carpeting. Hardware appointments include large, heavy-duty, metal comer protectors, recessed handles and large, rubber feet. In addition, sockets have been installed on the enclosure bottom for the use of removable casters. Casters are not included with your system and must be purchased separately— consult your Electro-Voice dealer. The B-410 input panel Incorporates two Neutrik Speakon™ NL4MPR-V connectors. The mating connector is the Neutrik Speakon NL4FC. One NL4FC connector is supplied with the B-410. These connectors were chosen because they are rugged, locking, easily wired, sealed and relatively inexpensive when compared to other professional connectors. Speakon connectors are rated for very high current, much more than this system should ever encounter. The connector's continuous current rating is 30 amps, many times that of ’/«-inch connectors. Speakon connectors also have a much lower contact resistance than even the highest quality ’/‘-inch connectors. B-410 and Speakon wiring diagrams are shown on the back of this data sheet (see Figure 1). Notice that in “normal" operation, pins 2+ and 2- would not be used, but they are “linked” to facilitate customized wiring schemes. POWER HANDLING TEST To our knowledge, Electro-Voice was the first U.S. manufacturer to develop and publish a power test closely related to real-life conditions. First, we use a random noise input signal because it contains many frequencies simultaneously, just like real voice or instrument program. Second, our signal contains more energy at extremely high and low frequencies than typical actual program, adding an extra measure of reliability. Third, the test signal includes not only the overall “long-term average” or “continuous” level—which our ears interpret as loudness—but also short-duration peaks which are many times higher than the average, just like actual program. The long-term average level stresses the speaker thermally (heat). The instantaneous peaks test mechanical reliability (cone and diaphragm excursion). Note that the sine-wave test signals sometimes used have a much less demanding peak value relative to their average level. In actual use, long-term average levels exist from several seconds on up, but we apply the long-term average for eight hours, adding another extra measure of reliability. Specifically, the B-410 is designed to withstand the power test described In EIA Standard RS-426A. The EIA test spectrum is appli...