Assessments - 4, GPA: 4.5
(
)
)
|
Facilidade de uso
• Only external hard drives* with external power supplies are supported. When using an ex- ternal hard drive, if you switch the Q Record "Off" and then back "On" again you will need to disconnect and then reconnect your external hard drive USB plug. If you do not do this the Q Record will not detect your connected hard drive. • If you are using a SD Card via USB SD Card reader, you must remove the USB SD Card reader first to change SD Card's. Please do not remove the SD Card from the USB SD Card reader while the USB card reader is still connected to the Q Record. Q Record Quick start instructions Quick start: American Audio® would like to thank you for your purchase of this great audio product. For those of you that don't have the time to read the entire user manual we have compiled these quick start instructions. We hope that you will at least read through these instructions to familiarize yourself with the basics of this mixer. The Q Record is part of American Audio’s continuing evolution in audio technology. This unit has been built and designed to meet the needs of a typical DJ. We have attempted to provide you with the most reliable product on the market by using only components constructed of the finest material. Master Level - Use this level to control your main volume output. Try never to send an output of more than +4dB to your system. Signal at levels higher than this will start to distort and may cause damage to your system and speakers. Remember that a distorted signal from your mixer will only be multiplied throughout your system. Channel GAIN Level - The channel gain levels are not to be used as volume controls. Never use the channel trim to set the output volume. These controls are used to aid in distortion control. Use these control to preset your signal level before the crossfader. With your channel faders in the maximum position, use the channel trim level to set an average output level of about +4dB on you master level meter. Headphones - To avoid damaging your headphones always be sure the headphone volume level (13) is set to minimum before plugging them in. To avoid sever hearing damage, never put the headphone on without making sure the headphone level is turned down. Main Mic - The main mic connector uses a combo plug that allows you to connect either a 1/4” unbalanced jack or by a standard 3-pin XLR balanced connector. The main mic also has an independent volume control. When feedback occurs when using the mic, try lowering the level this may reduce the feedback. Always leave the mic level to it’s minimum level when not in use. Note: We recommend that you use a 500-600ohm microphone for the best sound quality. PHONO/AUX Line Level Selector SWITCH - This switch is used to change the selected input from phono to line and vice versa. The switch selectors are on the rear panel. ©American Audio® - - Q Record Instruction Manual Page 7 Q Record Front Panel - Controls and Functions 2 1 3 4 5 6 7 8 9 24 23 22 12 11 10 13 14 15 16 17 18 21 19 20 1. Microphone 1 - This combo jack will accept a standard 1/4 plug or XLR 3-pin balanced male plug. The volume output level for this microphone will be controlled by its own respective VOLUME knob (22). Note: We recommend that you use a 500-600ohm microphone for the best sound quality. 2. SOURCE SELECTOR SWITCH - These switches are used to select the input source assigned to each channel. Each channel may only be assigned one input source at a time. This switch must be in the “phono” position for turntable operation. 3. Channel Gain Control - This adjustment is used to adjust the audio source signal input gain for a channel. Never use the gain control to adjust a channels output volume. Setting the gain level properly will ensure a clean output signal. An improper gain level adjustment will send a distorted signal throughout the entire audio line which may damage speakers and amplifiers. To properly set a channels gain level control: 1. Be sure the Master Volume Control (5) is set to level 8. 2. Set the Channel Fader (19) to level 8. 3. Begin playback on an audio source connected to the channel you are adjusting. 4. Use the Gain Control to adjust an average output volume of +4 dB. 5. Repeat this step for all channels 4. CHANNEL EQ SECTION - CHANNEL treble control - This knob is used to adjust the treble levels of a channel ©American Audio® - - Q Record Instruction Manual Page 8 allowing for a maximum treble gain of +12dB or maximum decrease of -30dB. Turning the knob in a counter-clockwise direction will decrease the amount of treble applied to a channel signal, turning the knob in a clockwise direction will increase the amount of treble applied to a channel signal. CHANNEL midrange control - This knob is used to adjust the midrange levels of a channel allowing for a maximum midrange gain of +12dB or maximum decrease of -30dB. Turning the knob in a counter-clockwise direction will decrease the amount of midrang...