Assessments - 4, GPA: 3.3
(
)
)
|
Facilidade de uso
CHANNEL 2: PHONO 2 INPUT/AUX 2 JACKS - The type of input must directly reflect the selected mode of the LINE LEVEL SELECTOR SWITCH (24). Connect turntables equipped with MM pickup cartridge to PHONO inputs (All DJ turntable use MM pick-up cartridges). CD players or Tape Decks and other line level instruments may be connected to these jacks as long as the Line Level Selector Switch (29) is in the “AUX 2” position. The red colored RCA jack represents the right channel input and the white represents the left channel input. 24. LINE LEVEL SELECTOR SWITCH - This switch is used to change the mode of PHONO INPUT JACKS (23 and 26). When connecting turntable to these jacks be sure the switch is in the PHONO position, and when using line level input devices select AUX. Always be sure main power is shut off before change the position of the Line Level Selector Switch. 25. CHANNEL 1: LINE 1 RCA INPUT JACKS -These Jacks are used for line level inputs. Connect CD players or Tape Decks to LINE inputs. Line level musical instruments with stereo outputs such as Rhythm Machines or Samplers should also be connected to LINE inputs. Turntables should only be connected to “Phono”inputs. The red colored RCA jack represents the right channel input and the white represents the left channel input. 26. CHANNEL 1: PHONO 1 INPUT/AUX 1 JACKS -The type of input must directly reflect the selected mode of the LINE LEVEL SELECTOR SWITCH (24). Connect turntables equipped with MM pickup cartridge to PHONO inputs (All DJ turntable use MM pick-up cartridges). CD players or Tape Decks and other line level instruments may be connected to these jacks as long as the LINE LEVEL SELECTOR SWITCH (24) is in the “AUX 1” position. The red colored RCA jack represents the right channel input and the white represents the left channel input. 27. GND (GROUND TERMINAL) - Connect each of your turntables ground leads to either of the two ground terminal. This will reduce the humming and popping noises associated with magnetic phono cartridges. ©American Audio® --Q-221™ Instruction Manual Page 8 Q-221™ Typical Mixer Set-Up CASSETTE DECK TURNTABLE TURNTABLE ©American Audio® - - Q-221™ Instruction Manual Page 9 Q-221™ Typical Mixer Set-Up Speaker Cables Stereo RCA to 1/4” Patch Cables ©American Audio® - - Q-221™ Instruction Manual Page 10 CASSETTE DECK V4000 Amplifi er Q-221™ Cleaning Q-221™ Cleaning Due to fog residue, smoke, and dust, cleaning the mixer should be carried out periodically to optimize light output. 1. Use normal glass cleaner and a soft cloth to wipe down the outside casing. 2. Use a cleaner specially designed for electronics to spray in and around the knobs and switch. This will reduce small particle built up that can effect the proper operation of the mixer. 3. Clean should be carried out every 30-60 days. 4. Always be sure to dry all parts completely before plugging the mixer in. Cleaning frequency depends on the environment in which the mixer operates (i.e. smoke, fog residue, dust, dew). Q-221™ Cross Fader Replacement The crossfader is “Hot Swappable” which means it may be replaced at any time, even when power is applied. Only replace with American Audio Feather Fader Plus. Replacing with any other model fader may seriously damage your mixer. Replacing the Crossfader: 1. Using a number two Phillips screw driver, unscrew the each of the stainless steel retaining screws that hold the crossfader in place. 2. Gently remove the crossfader from its seated position. You may need to wiggle the crossfader slightly to unseat it. 3. After removing the crossfader, disconnect the ribbon cable that attaches the crossfader to the PC board. Grasp the crossfader by its base and pull the ribbon cable by its connector not the actual cables. The connector is desired to only fit one way, so don’t worry about the connectors orientation. 4. Connect the new crossfader to the ribbon cable. 5. Reassemble in reverse order. ©American Audio® --Q-221™ Instruction Manual Page 11 Q-221™ Warranty Q-221™ Warranty The Q-221™ carries a two year limited warranty. We recommend you fill out the enclosed warranty card to validate your purchase. All returned service items whether under warranty or not, must be freight pre-paid and accompany a R.A.(return authorization) number. If the mixer is under warranty, you must provide a proof of purchase invoice. You may obtain a R.A. number by contacting our customer support team on out toll free number. Q-221™ Main Features 2-YEAR LIMITED WARRANTY A. American Audio® hereby warrants, to the original purchaser, American Audio® products to be free of manufacturing defects in material and workmanship for a period of 2 Year (730 days) from the date of purchase. This warranty shall be valid only if the product is purchased within the United States of America, including possessions and territories. It is the owner’s responsibility to establish the date and place of purchase...