Assessments - 6, GPA: 4
(
)
)
|
Facilidade de uso
Operational can be changed by the VOLTAGE SELECTOR (26) on the rear of the unit. Be sure the power switch is in the OFF position before making any type of connections to the mixer. Also be sure the power on all units being connected to the mixer have been switched off. Before switch the power on the mixer be sure MASTER VOLUME (13) is turned down and the power switch to all your amplifier are in the "OFF" position. Connect the mixers MASTER OUTPUT JACKS (31) to your audio system. Make sure that the channels are set properly. When using the BALANCED OUTPUT JACKS (30) be sure your cable follow the above Pin Configuration (Figure 3). For recording, connect your tape recorder or cassette deck to the REC OUT JACKS (33). The Record Out level will not be influenced by the MASTER VOLUME CONTROL (13). The Record Out (REC OUT) level is dictated by the CHANNEL FADER LEVEL (6). Connect a microphone to any of the two available MIC INPUT JACKS (15 & 38). You can connect 2 turntables using the PHONO 1 (37) or PHONO 2 (35) RCA jacks on the rear panel. The mixer will only accept turntable level signal if the LINE LEVEL SWITCHES (36) are in the "PHONO" position. Connect your tape recorder, tuner, sound effects, CD player, and cassette decks etc. to the RCA LINE LEVEL INPUT JACKS on the rear panel. CD players, cassette decks and other line level instruments may also be connected to the PHONO RCA JACKS as long as the LINE LEVEL SWITCHES are in the "AUX" position. ©American Audio® - - Q-2422/SX User Instructions page 14 SET-UP INSTRUCTIONS Typical Mixer Set-Up (Inputs) CD PLAYER .................. CASSETTE DECK PARAMETER TIMEPARAMETER RATIOEJECTPOWERCUE1 2 3 4 5 6 7 8 9 0RELOOPSINGLELOOPREMAINNONSTOPTOTALELAPSEDMTSPROGRAMLOCKKEYSYNC.BEATFPITCHBPMCUEAUTOBPMOFFONFXMIXBOPENTERPANFLANGERSKIDPHASEFX SELECTSGL/CTNTIMEREV.PLAYTEMPO LOCK4%/8%/16% TRANSECHOSCRATCHFILTERHOLDON/OFFSAMPLE PITCH .................. This image details a typical DJ Set Up consisting of a microphone, turntables, CD players, and a tape deck. Note: Turntables can only be connected to the PHONO LEVEL RCA JACKS (37, 35). Be sure the LINE LEVEL SELECTOR SWITCHES (36) are in the "PHONO" position when using turntables. ©American Audio® - - Q-2422/SX User Instructions page 15 SET-UP INSTRUCTIONS Typical Stereo Set-Up (Output) Figure 9 Typical Balanced Output Set-up This image details a typical stereo output layout. Note the use of the Balanced XLR Jacks on both the mixer and the amplifier. Always use the balanced output jacks whenever possible. The balanced output jacks should always be used for cable runs in excess of 10 feet. Using the balanced jacks will ensure a clean signal through out the entire audio system. ©American Audio® - - Q-2422/SX User Instructions page 16 OPERATING DETERMINATIONS Operating Determinations When installing this mixer, please make sure that the device is not exposed to extreme heat, moisture or dust! There should not be any cables lying around. Doing so endangers you as well as others. Do not operate the mixer in extremely hot (more than 30°C/100°F) or extremely cold (less than 5°C / 40°F) surroundings. Keep away from direct sunlight and heaters. Operate the mixer only after becoming familiar with its functions. Do not permit operation by persons not qualified for operating the mixer. Most damages are the result of unprofessional operation! Never use spray cleaners to clean the faders! Never use solvents or abrasive detergents to clean the mixer! It is recommended that you use a soft damp cloth. Please consider that unauthorized modifications on the device are forbidden due to safety reasons! CROSSFADER REPLACEMENT INSTRUCTIONS The crossfader is "Hot Swappable" which means it may be replaced at any time, even when power is applied. Only replace with American Audio Part Feather Fader Plus. Replacing with any other model fader may seriously damage your unit. Replacing the Crossfader 1. Disconnect the mixers main power supply 2. Using a number two Phillips screw driver, unscrew the each of the stainless steel retain screws that hold the crossfader in place. 3. Gently remove the crossfader from its seated position. You may need to wiggle the crossfader slightly to remove it. 4. After removing the crossfader, disconnect the ribbon cable that attaches the crossfader to the PC board. Grasp the crossfader by its base and pull the ribbon cable by its connector not the actual cables. The connector is designed to only fit one way, so don't worry about the connec- tors orientation. 5. Connect the new crossfader to the ribbon cable and replace in reverse order. ©American Audio® - - Q-2422/SX User Instructions page 17 TECHNICAL SPECIFICATIONS Technical Specifications - Model Q-2422/SX Model: Q-2422/SX™, 2 Channel Mixer Power supply: AC 115/230V, 50/60Hz selectable Dimensions: 19” W x 7” D x 2.25” H / 482x 176x 65mm Weight: 8.5 lbs. / 3.8 kg Crossfader: FF-Plus - Optic...