Assessments - 1, GPA: 3
(
)
)
|
Facilidade de uso
Use ZONE 1 / ZONE 2 VOLUME (23) and ZONE BASS & TREBLE (24) knobs to control the output signal for their respective ZONES. ZONE 1 & ZONE 2 each have their own MONO/STEREO SWITCH (26). ZONE 1 output is the same as MASTER program (31), while ZONE 2 is selectable from any of the 4 channels (17) or PROGRAM MIX (PGM) (19). (26) ZONE 2 ASSIGN -ZONE 2 may be assigned to any of the 4 channels (17) or PROGRAM MIX (PGM) (19). (27) SEND CONTROL -Controls output to effects (ie. echo boxes, phasers, reverb, etc.). (28) RECEIVE CONTROL -Controls the input from effect (ie. echo boxes, phasers, reverb, etc.). (29) SEND / RECEIVE ON / OFF SWITCH -Turns SEND (27) & RECEIVE (28) CONTROLS ON / OFF. Red LED will light when switch is ON. (30) BNC-JACK FOR GOOSENECK LAMP - 12V DC (31) MASTER FADER -Adjusts the level of the master output. (32) MASTER MONO/STEREO SWITCH -Used to set the master output to mono or stereo. If this switch is set to STEREO, the master signal is sent to the MASTER OUT jacks (43). For mono and bridged operation, set this switch to MONO, and connect your amplifier with the 3-pin XLR jacks on the rear panel, the BALANCED OUTPUT jacks (47). (33) BALANCE CONTROL - Used to adjust how much of the signal is sent to the left and right MASTER OUT jack (43). (34) MASTER LEVEL DISPLAY -The LEDs show the signal level of the right and left master level output. XDM-3633 User Instructions page 6 Inputs and Outputs (Rear Panel) LINE 1 CH-1 PHONO 1 AUX 1 LINE 2 CH-2 PHONO 2 AUX 2 MASTER OUTPUT REC L R 50 AUX 2 PHONO 2 AUX 1 PHONO 1 47 GND LIGHT CONTROL 42 4135b CH-3CH-4 MIC 3 PHONO 3 AUX 3 LINE 3LINE 4ZONE 1ZONE 2 LINE 5 LINE 6 SEND EFFECT RECEIVE BALANCED OUTPUT RIGHT LEFT AUX 3 PHONO 3 115V AC VOLTAGE SELECTOR AC INPUT 115/230V FUSE GND 49 48 46 45 44 4043 39 38 37 38 35a (35a) (35b) GND (GROUND TERMINALS) -Connect the ground lead of the turntables with this terminal. This helps to reduce humming and popping noises. There are two convenient ground terminals located on the rear of the mixer. (36) MIC 3 JACK -Connect your third microphone with 1/4 inch (6.3mm) jack plug here. To use MIC 3, CH-4 LINE 5/ LINE 6/MIC 3 SWITCH (3) must be switched to MIC 3. To turn MIC 3 OFF, change the LINE 5/LINE 6/MIC 3 SWITCH to LINE 5 or LINE 6. (37), (38), (39), (40) LINE / PHONO / AUX INPUT JACKS -Input jack for CH-1, CH-2, CH-3 and CH-4. Connect turntables equipped with MM pickup cartridge to PHONO inputs. CD players or Tape Decks should be connected to LINE input. Line level musical instruments with stereo outputs such as Rhythm Machines or Samplers should also be connected to LINE inputs. CHANNEL 1 (37) features left and right RCA inputs for LINE 1 and PHONO 1 / AUX 1. CHANNEL 2 (38) features left and right RCA inputs for LINE 2 and PHONO 2 / AUX 2. CHANNEL 3 (39) features left and right RCA inputs for LINE 3, LINE 4 and PHONO 3 / AUX 3. CHANNEL 4 (40) features left and right RCA inputs for LINE 5 and LINE 6.Other inputs (ie. CD players) may also be used in the PHONO/AUX RCA jacks(37, 38, 39) when the PHONO/AUX SELECTOR SWITCH (41) is set to AUX. (41) PHONO / AUX SELECTOR SWITCH -Changes phono to an extra line; allows the DJ to use a CD player or other input device in the same line as the phono line. When using a turntable select PHONO, and when using other input devices select AUX. PHONO/AUX lines can be used with LINES 1, 2, and 3. The PHONO /AUX SELECTOR SWITCH gives the DJ the possibilities of 3 extra inputs lines (ie. 3 lines CD, tape etc.). (42) INDEPENDENT LIGHT CONTROL -Buffered audio output for light controllers that can use external input. Great for Touch Panels and Chase Controllers. (43) MASTER OUT -Parallel output of P.A. output. Connect with the input of a power amplifier. Make sure that the STEREO/MONO switch (32) is set to STEREO. (44) REC OUT -Connect to your record unit. The REC OUT level is not influenced by the MASTER FADER (31). (45) ZONE 1 & ZONE 2 OUTPUTS -Left & Right RCA output jacks controlled by the ZONE 1 & ZONE 2 (24, 25, 26) controls on the front panel. (46) SEND & RECEIVE EFFECTS -Left & Right 1/4” stereo jacks for SEND (27) & RECEIVE (28) EFFECTS. (47) BALANCED OUTPUT -Balanced output for the master signal. (48) AC CONNECTION -Standard IEC plug with detachable AC power cord. (49) FUSE -Fuse holder. Only replace the fuse when the device is disconnected from main power supply. Only replace with fuses of the same power rating. (50) AC VOLTAGE SELECTOR -Select between 115V/50Hz or 230V/60Hz. Make sure that the selector is set to the proper voltage you are using. XDM-3633 User Instructions page 7 Replacing the Crossfader • Disconnect from main power supply • Remove the fader knob. • Remove the two outer screws. • Take the fader out and unplug the connection cables. • Connect the new fader and replace back into mixer. Technical Specifications - model XDM-3633 Inputs: Line: 75mV, 27k Ohm • Microphone: 1.5mV, 600 Ohm • Phono: 1.2mV, 47k Ohm Output: Line: 9V, peak to peak • Headphones: 5W @ 47 Ohm • Distortion: ...