Assessments - 5, GPA: 3.8
(
)
)
|
Facilidade de uso
Channels 1 and 2 may be switched PHONO or LINE. Use “LINE” for line level devices such as CD players and tape decks. Use “PHONO” for magnetic turntables only (DJ turntables). CHANNEL GAIN LEVEL (13) - The channel gain levels are not to be used as volume controls. Never use the channel trim to set the output volume. These controls are used to aid in distortion control. Use these control to preset your signal level before the crossfader. With your channel faders in the maximum position, use the channel trim level to set an average output level of about +4dB. HEADPHONES (6) -To avoid damaging your headphones always be sure the headphone volume level (11) is set to minimum before plugging them in. To avoid sever hearing damage, never put the headphone on without making sure the headphone level is turned down. MIC (7) - The mic connector uses a 1/4” plug that allows you to connect a 1/4” unbalanced mic cord. The mic also has an independent volume control. Always leave the mic level to it’s minimum level when not in use. Q-START FEATURE -This function works in conjunction with a compatible American Audio or American DJ “Q”Start CD player. When used with a compatible CD player, you can use the crossfader to start and stop the CD Player with the slide of the fader. The ON/OFF “Q ”START switch activates this FADER “Q ”START feature. ©American Audio® --Q-D1™ Instruction Manual Page 7 Q-D1™ CONTROLS AND FEATURES 11110981354321276 Q-D1™ CONTROLS AND FEATURES 11110981354321276 1. MASTER VOLUME CONTROL -This rotary knob is used to control the master output level (volume). To avoid distorted output try to maintain an average output signal level +4 dB. Be sure this volume control is always set to zero before turning the unit on. 2. MIC LEVEL -This rotary knob is used to control the microphone volume output level. Turning the knob in a clockwise direction will increase volume output. 3. CHANNEL BASS CONTROL - This knob is used to adjust the low frequency levels of a channel allowing for a maximum bass gain of 12dB or maximum signal decrease of -26dB. Turning the knob in a counter-clockwise direction will decrease the amount of bass applied to a channel signal, turning the knob in a clockwise direction will increase the amount of bass applied to a channel signal. 4. CUE MIXING CONTROLLER -This switch selects the channel for monitoring. The monitor signal comes from the Prefader. This means it will not be affected by the channel faders. You can monitor each channel individually. Connect your headphones to the HEADPHONES jack. Flip the CUE MIXING CONTROL switch to channel you wish to monitor. If the CUE MIXING CONTROL is set to the center position, you can monitor both the channels at once. 5. “Q” START ON/OFF -This function works in conjunction with a compatible American Audio® "Q" ©American Audio® --Q-D1™ Instruction Manual Page 8 Q-D1™ CONTROLS AND FEATURES CONT. Q-D1™ CONTROLS AND FEATURES CONT. For example, each time you slide the crossfader to the far left, the "Q" start function will trigger the play mode for any CD player connected to PLAYER CONTROL "A". Play will begin at that unit's last set cue point. Turn the "Q" ON/OFF SWITCH to the OFF position to disengage “Q” Start function and resume normal fader operation. 6. HEADPHONE JACK -This jack is used to connect your headphones to the mixer allowing you to monitor the cue source. Use headphones only rated at 8 ohms to 32 ohms. Most DJ headphones are rated at 16 ohm, these are highly recommended. Always be sure the CUE VOLUME LEVEL (11) is set to minimum before you put the headphones on. 7. MICROPHONE CONNECTOR -This jack is used to a connect a microphone to the mixer. Connect your microphone via this 1/4 inch (6.3mm) jack. The signal volume will be controlled by the Mic Level (2). 8. FEATHER FADER PLUS CROSSFADER - This fader is used to blend the output signals of channels one and two together. When the fader is in the full left position (channel 1), the output signal of channel one will be controlled by the master volume level. The same fundamentals will apply for channel two. Sliding the fader from one position to another will vary the output signals of channels one and two respectively. When the crossfader is set in the center position, the output signals of both channel one and channel two will be even. 9. CHANNEL VOLUME FADER -These faders are used to control the output signal of any source assigned to its particular channel. However, master volume is controlled by the MASTER VOLUME CONTROL (1). 10. SOURCE SELECTOR SWITCH - These switches are used to select the input source assigned to each channel. Each channel may only be assigned one input source at a time. This switch must be in the “PHONO” position for turntable operation. 11. CUE LEVEL VOLUME CONTROL -This knob adjusts the headphone volume output level. Turning the knob in clockwise direction will increase headphone volume output. 12. CHANNEL TREBLE CONTROL -This kn...