When headphones are connected to the amplifier, the internal speaker is automatically turned off. NOTE: The headphone system will not work with headsets equipped with a mono phone plug. LINE CORD (120V PRODUCTS ONLY) (19) For your safety, we have incorporated a 3-wire line (mains) cable with proper grounding facilities. It is not advisable to remove the ground pin under any circumstances. If it is necessary to use the equipment without proper grounding facilities, suitable grounding adaptors should be used. Less noise and greatly reduced shock hazard exists when the unit is operated with the proper grounded receptacles. SPECIFICATIONS POWER AMP SECTION Rated Power & Load: 65 W RMS into 8 ohms Power @ Clipping: (typically) (5% THD. 1 kHz, 120 V AC line) 65 W RMS into 8 ohms 4 ohms not recommended Frequency Response: +0. -2 dB, 20 Hz to 10 kHz @ 50 W into 8 ohms Total Harmonic Distortion: Less than 0.2%, 100 mW to 50 W RMS. 60 Hz to 10 kHz, 8 ohms (typically below 0.1%) Hum & Noise: Greater than 78 dB below the rated power Power Consumption: 200 W. 50/60 Hz. 120 V AC PREAMP SECTION The following specs are measured @ 1 kHz with the controls preset as follows: Push Bright Off (Out) Channel Select Normal (Out) Low & High @ 10 Mid @ 0 w SuperSat® & Post Gain @ 10 Pull gain Off (In) Bottom, Body. & Edge 0 dB Nominal levels are with normal gain @ 5 Minimum levels are with normal gain @ 10 Preamp High Gain Input: Impedance: High Z. 220 K ohms Nominal Input Level: -16 dBV. 150 mV RMS Minimum Input Level: -34 dBV. 20 mV RMS Maximum Input Level: +16 dBV, 6 V RMS Preamp Low Gain Input: (10 dB pad) Impedance: High Z. 69 K ohms Nominal Input Level: -6 dBV. 450 mV RMS Minimum Input Level: -24 dBV. 60 mV RMS Maximum Input Level: +26 dBV. 18 V RMS BLOCK DIAGRAM Effects Return: Impedance: High Z. 22 K ohms Designed Input Level: -10 dBV. 0.3 V RMS (Switching jack providing Effects Send to Effects Return connection when not used) System Hum & Noise @ Nominal Input Level: (20 Hz to 20 kHz unweighted) 74 dB below rated power Equalization: (Normal Channel Only) Special Low. Mid. & High passive type EQ Push bright: +6 dB @2 kHz Voicing: Special Bottom. Body, & Edge active type EQ Pull Gain: Increases SuperSat; gain External Footswitch Function: Reverb Defeat (when reverb control is raised) Lead Channel Defeat (when selected with button) LEAD SUPER GAIN POST iMP VOICING INPUT /77 PUSH CHANNEL NORMAL T-iij blé-ci »ho«* signai Us» »¡Irin ifK uni in trttt l* Ihc.'cyghlf uiys»'»;*nc tn* Ltii!1* Iirttiwn iljif Or WOC* C*ikjÜY. TONE SETTING HIGH LOW SAIN CSA1M Ы0ЯМЛ1 GAIN ■COUAl I7ATION- Qmm э Q-eoeano STUDIO PRO 110 SUPERSATÏ> POST BOTTOM 600V EOCE I SENO RETURN I LEVEL ADJUST TO TASTE CLEAN ACTIVATE PULL GAIN METAL ADJUST TO TASTE HIGH LOW GAIN GAIN HOftUAi GAIN -t OUAl 17 AIIO H - 801 TOU 800v ADJUST TO TASTE ACTIVATE COUNTRY-CLEAN pull gain COUNTRY LEAD \WL11 NÜ1IUAL QAIN y-EQUALISATION-y /-1 FAC GAIN-4 /-VOICING-^ 010 э 0 3 6 ® -u I—I D 'i' »• OJUS* TO TASTE JAZZ SUPERSAT' POST ACTIVATE PIJLL GAIN MEDIUM DISTORTION ADJUST TO TASTE Tone settings giver, sre generas ana will vary according to type of guitar, type and guages of strings, type Ы pickup ала even type ci pick. Personal taste, playing style, and type of music greatly cortrûute to desired lonafcy, ESPAÑOL Consulte los diagramas del panel delantero en la sección de inglés de este manual. HIGH GA1N INPUT (Entrada de ganancia alta) (1) Se usa para la mayoría de las guitarras eléctricas. Tiene 6 dB más volumen que la entrada de baja ganancia. LOW GAIN INPUT (Entrada de baja ganancia) (2) Se suministra para instrumentos que tienen una salida extremadamente alta, la cual puede causar la sobrecarga (distorsión) de la entrada de alta ganancia. Si se usan ambas entradas simultáneamente, el nivel de salida es el mismo (ambos son de baja ganancia). NORMAL GAIN (Ganancia normal) (3) Controla el nivel de volumen del canal Normal y no es afectado por los controles SuperSat o Ganancia posterior. BRIGHT SWITCH (Interruptor de brillo) (4) Proporciona un impulso preajustado de +6dB a las frecuencias agudas. Para activarlo, empuje el interruptor a la posición “hacia dentro'’. CHANNEL SELECT SWITCH (Interruptor para selección del canal) (5) Permite la selección del canal “lead” (solista) o normal. La posición hacia dentro selecciona el canal ¿iead?’ y la posición hacia fuera selecciona el canal normal. NOTA: La selección del canal puede lograrse también con el pedal interruptor de control remoto. Si se desea hacer selección con control remoto, el interruptor de canal debe estar en la posición hacia dentro (“lead'%). LOW, MID, & HIGH EQ (Ecualizador de frecuencias graves, medias, y agudas) (6) Controles de tono pasivo que regulan las frecuencias graves, medias, y altas, respectivamente. SUPERSAT®/PULL GAIN (SuperSat/Control que se tira para obtener ganancia) (7) Es una simulación con...
)
