Assessments - , GPA:
(
)
)
Fabricante : Peavey
Arquivo Tamanho: 1.04 mb
Arquivo Nome : 03588440_10146.pdf
Língua de Ensino: 
O documento está colocado, por favor, espere
 |
O documento está colocado, por favor, espere
Facilidade de uso
LEAD CHANNEL RESONANCE CONTROL Adjusts the low-frequency damping factor of the power amplifier, which gives the amp a "tighter" sound when fully dialed counter clockwise and an increasingly "looser" sound when adjusted clockwise. LEAD CHANNEL PRESENCE CONTROL Adjusts the high frequency damping factor of the power amplifier, which gives the amp a "mellow" character when fully counter-clockwise and more of "biting" or forward character when rotated clockwise. RHYTHM CHANNEL RESONANCE CONTROL Adjusts the low-frequency damping factor of the power amplifier, which gives the amp a "tighter" sound when fully dialed counter clockwise and an increasingly "looser" sound when adjusted clockwise. RHYTHM CHANNEL RESONANCE CONTROL Adjusts the high frequency damping factor of the power amplifier, which gives the amp a "mellow" character when fully counter-clockwise and more of "biting" or forward character when rotated clockwise. MASTER REVERB CONTROL Controls the amount of spring reverb in the signal chain. LEAD CHANNEL POST CONTROL This control adjusts the volume of the lead channel. HIGH CONTROL This passive control regulates the high frequencies for the Lead channel. MID CONTROL This passive control regulates the mid frequencies for the Lead channel. LOW CONTROL This passive control regulates the low frequencies for the Lead channel. PRE GAIN CONTROL Adjusts the amount of gain in the Lead Channel. Turning this knob clockwise will increase the amount of distortion present in the signal. LEAD CHANNEL INDICATOR LIGHT This light is on when the Lead Channel is active. 8 Front Panel 15161718192021221516171819202122 14 15 16 17 18 19 20 21 22 RHYTHM CHANNEL POST CONTROL This control adjusts the volume of the Rhythm channel. HIGH CONTROL This passive control regulates the high frequencies for the Rhythm channel. MID CONTROL This passive control regulates the mid frequencies for the Rhythm channel. LOW CONTROL This passive control regulates the low frequencies for the Rhythm channel. RHYTHM CHANNEL CRUNCH SWITCH Engaging this switch turns on the crunch effect, increasing the amount of distortion present in the signal on the Rhythm channel. PRE GAIN CONTROL Adjusts the amount of gain in the Rhythm channel. Turning this knob clockwise will increase the amount of distortion present in the signal. RHYTHM CHANNEL INDICATOR SWITCH This light is on when the Rhythm channel is active. CHANNEL SWITCH Switches between the Rhythm and Lead channel. INPUT JACK 1/4" Instrument input jack. 9 Rear Panel 2325242627282930Rear Panel 2325242627282930 23 24 25 26 27 28 29 30 EFFECTS LOOP 1/4" Send and Return jacks for the effects loop. CABINET IMPEDANCE SELECTOR SWITCH This three-position switch allows appropriate selection of speaker cabinet impedance. If two enclosures of equal impedance are used, the switch should be set to half the individual value. For example, two 16-Ohm enclosures necessitate an 8-Ohm setting, while two 8-Ohm enclosures would require a 4-Ohm setting. Minimum speaker impedance is 4 Ohms. The stock setting for the internal speaker is 16 Ohms. SPEAKER OUTPUTS These paralleled 1/4" mono (TS) jacks are provided for the connection of speaker enclosure(s). Again, minimum speaker impedance is 4 Ohms. The CABINET IMPEDANCE SWITCH (23) should be set to match the load of the speaker cabinet(s). MSDI™ Microphone Simulated Direct Interface. Peavey's exclusive MSDI simulates teh sound of a microphone about 8" from teh cone, allowing the user to send a clean signal to the mixing console. This is a non powered output and safe for use with any mixing console. GROUND LIFT Engage this switch if the mix engineer is hearing a hum in the MSDI output, this should eliminate the hum. FOOTSWITCH 1/4" input for the optional footswitch. FUSE A fuse is located within the cap of the fuse holder. This fuse must be replaced with one of the same type and value to avoid damaging the amplifier and voiding the warranty. If the amp repeatedly blows the fuse, it should be taken to a qualified service center for repair. WARNING: THE FUSE SHOULD ONLY BE REPLACED AFTER THE POWER CORD HAS BEEN DISCONNECTED. IEC MAINS CONNECTOR This is a standard IEC power connector. An AC mains cord having the appropriate AC plug and ratings for the intended operating voltage is included in the carton. The mains cord should be connected to the amplifier before connecting to a suitable AC outlet. U.S DOMESTIC AC MAINS CORD The mains cord supplied with the unit is a heavy-duty, 3-conductor type with a conventional 120 VAC plug with ground pin. If the outlet used does not have a ground pin, a suitable grounding adapter should be used, and the third wire should be grounded properly. Never break off the ground pin on any equipment. It is provided for your safety. NOTE: FOR UK ONLY If the colors of the wires in the mains lead of this unit do not correspond with the colored markings identifying the terminals in your plug, proceed as follows: (1) The wire that is colored green and yellow mu...