Assessments - 3, GPA: 4.3
(
)
)
|
Facilidade de uso
Rotate clockwise to increase the effect. Remote footswitch can control On/Off. POST GAIN (9) Controls the overall volume level of the Lead channel. The final level adjustment should be made after the desired sound has been achieved. PRE GAIN (10) Controls the input volume level of the Lead channel. NORMAL GAIN (11) Controls the volume level of the Normal channel. BRIGHT INPUT (12) Input for instrument-level signals. This input produces enhanced high frequency response (treble), similar to a bright switch when compared to the normal input. NORMAL INPUT (13) Input for instrument-level signals. For brighter frequency response (highs) see Bright Input No. 12. 3 © @ T?¿ossic, /00 a pnocMcr or pexvsv ELscmoNics corp. MtfuoiAM. ms madcinuaa. # 9 3PtA№RtXJrPVrrS ©—i @ FUSE (14) The fuse is located within the cap of the fuseholder. If the fuse should fail, IT MUST BE REPLACED WITH THE SAME TYPE AND VALUE IN ORDER TO AVOID DAMAGE TO THE EQUIPMENT AND TO PREVENT VOIDING THE WARRANTY. If the amp repeatedly blows fuses, it should be taken to a qualified service center for repair. WARNING: THE FUSE SHOULD ONLY BE REPLACED WHEN THE POWER CORD HAS BEEN DISCONNECTED FROM ITS POWER SOURCE. GROUND SWITCH (15) Three position rocker-type switch which, in most applications, should be operated in its center or zero position. There may be some situations when audible hum and/or noise will come from the loudspeaker. If this situation arises, position the ground switch to either positive or negative (+ or -) or until the noise is minimized. NOTE: Should the noise problem continue, consult your Authorized Peavey Dealer, the Peavey Factory, or a qualified service technician. THE GROUND SWITCH IS NOT FUNCTIONAL ON 220/240 VOLT MODELS. SPEAKER OUTPUTS (16) A Provided for connection of external speakers). Minimum total impedance is 4 ohms. The speaker jacks are wired in parallel. For example, two 8 ohm speakers can be plugged into each one of the speaker output jacks for total load impedance of 4 ohms. However, only one 4 ohm speaker may be plugged in at a time. REMOTE SWITCH JACK (17) Provided for the connection of the optional remote footswitch. Foots witch is used to select the Lead or Normal channels and defeat reverb. When using remote footswitch, always insert the plug fully (second click) to ensure proper operation. IMPEDANCE SELECTOR SWITCH (18) Use to select the appropriate impedance of the speaker(s). For example, if two speakers of equal impedance are used, the switch should be set to one-half of that value. If two 16 ohm cabinets are used, the impedance selector should be set to 8 ohms. EFFECTS RETURN (19) Input for returning signals from external effects or signal processing equipment. EFFECTS SEND (20) Output for supplying signals to external effects or signal processing equipment. 4 TONE SETTING ■MASTER- -EQUALIZATION---VOLUME LEAD 67 67 67 67 67 67 6 7 „ 67„ „ - „ fT'*. .rr\, ,K2\, s( 1 /10 31 Jl0 3( T y 10 31 ^ Jl0 3( ‘WJkmI )l0 3^^ J103I ^■1031 )1 2V y11 2V y 11 2V __/11 2V /11 2V W11 aV y\\ 2\” /11 2V 7n 2V /11 1--12 1--M2 1--12 1 -M2 1 M2 1---12 1 -M2 l"--12 1--12 / PRESENCE VOLUME TREBLE MIDDLE BASS REVERB POST PRE NORMAL / INPUTS USED FOR BRIGHTER ADJUST TO TASTE ADJUST TO TASTE SOUND WITH ROCK ENHANCED HIGHS • MASTER---EQUALIZATION---VOLUME LEAD c 7 67 67 67 67 67 6 7 6 7 5/---^.8 5^—-N.8 . 5/---^8 5-^—\8 5^--s.8 5^--v.8 5.--^8 5^—^8 5-.---^8 if ^9 4/ y nf 4/ y 4/ \9 ni y v Y V y A ^BlO 3( Jiosi ^■103!^^ )i0 3( ^r103( /103^r J10 A W )i° jv 2V y 11 2V ^/11 2V ^11 2^r J11 2V 2V __X11 2\" >/11 2V wVl 2V /11 1 — 12 1 - 12 r-M2 1*---12 r-M2 1--M2 f*-"12 1 - 12 Is-“12 PRESENCE VOLUME TREBLE MIDDLE BASS REVERB POST PRE NORMAL INPUTS ADJUST TO TASTE ADJUST TO TASTE SELECT DESIRED INPUT METAL MASTER- -6QUALIZATION- LEAD 67 57 67 67 5^—"sS ------^8 —^8 'A X:( \ ;(▼); ;<* > f *) 2V ,/11 2V ^/11 2V >/11 2\. /11 2V y « 1 “ Mo < ■ ''l r» r» H***’ ■ ■■***'?'’) 12 1 12 1 12 1---12 PRESENCE VOLUME TREBLE MIDDLE BASS REVERB POST PRE NORMAL INPUTS ADJUST TO TASTE ADJUST TO TASTE SELECT DESIRED INPUT COUNTRY Tone settings given are general and will vary according to type of guitar, type and gauges of strings, type of pickup and even type of pick. Personal taste, playing style, and type of music greatly contribute to desired tonality. 5 SPECIFICATIONS POWER AMPLIFIER SECTION 8 - 6BQ5/EL84’s with 12AX7 driver Rated Power & Load: 100 W RMS into 16, 8, or 4 ohms Power @ Clipping: (Typically) (5% THD, I kHz, 120 Y AC line) 100 W RMS into 16, 8, or 4 ohms (Bias must be reduced to measure) Frequency Response: +0, -2 dB, 50 Hz to 15 kHz, @ 40 W RMS into 16 ohms Hum & Noise: Greater than 80 dB below rated power Power Consumption: 400 watts, 50/60 Hz, 120 V AC (Domestic) PREAMP SECTION 2 - 12AX7’s The following specs are measured @ 1 kHz with the controls preset as follows: Pre & Post (lead) @ 0 Reverb Level @ 0 Bass & Treble EQ @ 12 Middle EQ @ 0 Master Volum...