Assessments - 2, GPA: 4
(
)
)
|
Facilidade de uso
IM-M3000SiDAA Rev S4 PPrreelliimmiinnaarryy Mercury™ 3000Si Dual Axis AveragerMMoottiioonn CCoonnttrrooll FFeeeeddbbaacckk UUssiinngg AAvveerraaggiinngg ooff TTwwoo SSeennssoorrss IInnssttaallllaattiioonnMMaannuuaall aannddRReeffeerreenncceeGGuuiiddee Manual No. IM-M3000SiDAA Rev S4 PPrreelliimmiinnaarryy MicroE Systems was founded to advance encoder technology to a level never before achieved. Our objective was to design encoder systems that would be small enough to fit into densely packed OEM equipment designs, affordable enough for cost-sensitive applications and easy enough to enable installation, setup and alignment by assemblers with little training. We are pleased to say that all of these goals have been realized with the introduction of Sensor shown actual size the Mercury family of encoders M10 T TTa aab bbl lle ee O OOf ff C CCo oon nnt tte een nnt tts ss SYSTEM ILLUSTRATION PAGE Encoder with Linear scale 2 Encoder with Rotary scale 3 INSTALLATION INSTRUCTIONS Encoder System Mounting - Linear 4 Encoder System Alignment - Linear 5 Centering the Index & Calibration - Linear 5 Encoder System Mounting - Rotary 6 Encoder System Alignment - Rotary 7 Centering the Index & Calibration - Rotary 7 REFERENCE SECTION Installation of Linear Scales 8 Grounding Instructions 9 Recommendations for Power 9 Customer Interface Cable Requirements 10 Serial Output Specifications 11-12 SMARTPRECISION SOFTWARE INSTALLATION 13-19 SPECIFICATIONS Operating and Electrical 20 Output Connector Pinout 20 Serial Output 21 Operational Modes: Standard Communication 21 Serial Output Specificattion 22 Operational Modes - Trigger Approach Diagram 23 Serial Data Format 24 ENCODER TROUBLESHOOTING Selected Topics 24 Cleaning Scales 25 Contact MicroE Systems Back Cover Follow standard ESD precautions. Turn power off before connecting the sensor. 1 Do not touch the electrical pins without static protection such as a grounded wrist strap. Do not touch the glass scale unless you are wearing talc-free gloves or finger cots. 2 Please read this installation manual for full instructions. Safety Information MicroE Systems Mercury series reflective encoders are classified as CDRH Class I and IEC Class 1M laser products. • Invisible laser radiation (wavelength: 850 nm). Max power 1.5 mW CW. • This product conforms to all applicable standards under 21 CFR Ch. I 1040.10. • CDRH Class I level of laser radiation is not considered to be hazardous. • CAUTION - The use of optical instruments with this product will increase eye hazard. • DO NOT VIEW DIRECTLY WITH OPTICAL INSTRUMENTS (MICROSCOPES, EYE LOUPES OR MAGNIFIERS) • CLASS 1M LASER PRODUCT • IEC 60825-1 (2001) PPrreeccaauuttiioonnss PPaatteennttssAdditional patents and patents pending may apply. Covered by the following patents: US 5,991,249; EP 895,239; JP 3,025,237; US 6,897,435; and EP 1,451,933. Page 1 Mercury 3000Si Encoder System with Linear scale Page 2 Expanded View Scale benching edge End locator pin End index mark Sensor mounting holes (2) Bracket mounting holes (2) per sensor Optional sensor benching pins (3) Double shielded cables Center index mark Typical user-supplied sensor mounting brackets Top reflective linear scale Detail A 25 pin High Density D-sub connector Signal - Sensor 1 System View Shown with linear scale Glass scale (shown mounted on a linear slide) Sensors (shown attached on a linear slide base with mounting brackets) Dual Axis/SmartPrecision electronics module (interpolator) Scale reference datum; example shown with benching pins Cover: Sensor cables and connectors Power/Calibration - Sensor 1 Index Calibration Button - Sensor 1 and 2 Signal - Sensor 2 Power/Calibration - Sensor 2 USB interface Mounting screws & flat washers (2 needed per screw) Sensor 1 Sensor 2 Mercury 3000Si Encoder System with Rotary scale Page 3 Double shielded cable System View Shown with Rotary scale Sensors (shown attached to a customer-supplied mounting brackets) Rotary scale Dual Axis/SmartPrecision electronics module (interpolator) Expanded View Rotary scale Mounting hole (2) Top reflective rotary scale Typical user-supplied sensor mounting bracket Mounting screws & flat washers (2 needed per screw) 25 pin High Density D-sub connector Signal - Sensor 1 Power/Calibration - Sensor 1 Index Calibration Button - Sensor 1 and 2 Signal - Sensor 2 PowerPower/Calibration - Sensor 2 USB interface Sensor 1 Sensor 2 Installation Instructions Linear Encoders - Mounting Page 4 1 2 Install the sensors on your mounting surfaces referencing the appropriate datum surface as shown on the interface drawing. Use 2 washers per mounting screw. Benching pins may be used to locate each sensor if the system mechanical tolerances are adequate. See data sheet for alignment tolerances, or keep mounting screws loose for sensor alignment if benching pins are not used. Attach the scale to the base slide. Reference the preferred datum on the interface drawing for either end or center index orientation. Depending on the mount...