Assessments - 3, GPA: 3.3
(
)
)
|
Facilidade de uso
The CH FADER (26, 32) also affect each of the DUAL VU METER (40). NOTE: WHEN USING THE EFX SECTION, YOU MAY EXPERIENCE A TONAL BOOST THAT WILL SEND YOUR MASTER OUTPUT LEVELS INTO THE BLUE (0 THROUGH +11), AS INDICATED IN YOUR VU METER (40). ADJUST THE CHANNEL FADERS (26, 32), IN ORDER TO PROTECT YOUR EQUIPMENT FROM A SYSTEM OVERLOAD. TO BEGIN EFX EXPERIMENTATION, START WITH A LOW PARAMETER SETTING WITH YOUR CHANNEL FADERS (26, 32) AT MID LEVEL. THEN MOVE SLOWLY THROUGH THE EFX PARAMETERS TO EXAMINE THE TONAL BOOST, SAFELY. The PMX-05 is equipped with DIGITAL SIGNAL PROCESSOR (DSP) effects. This means you may augment the audio output of your program mix by processing tones through the 26 different effects. When an audio signal is processed through the DSP, a wide range of effects can be achieved with the PMX-05 EFX section. Please follow these instructions to operate the EFX section of your mixer: 1. DRY/WET FADER: To control this section you must adjust the DRY/WET FADER (34) in order to increase the level of the effect. Glide the DRY/WET FADER (34) to the RIGHT to increase the effect, saturating the PGM with WET effects. Glide the DRY/WET FADER (34) to the LEFT or DRY area to decrease the effect, thus disabling all effects. 2. EFX ON/OFF: The EFX ON/OFF (38) button has multiple functions: - PGM MODE: Tap the EFX ON/OFF (38) button. The blue LED will turn on to indicate that the DSP effects feature has been engaged in PGM mode. Tap the EFX ON/OFF (38) button again and the DSP effects will be disengaged as the LED turns off. When using the EFX ON/OFF (38) button, you will notice that once an effect has been engaged, the effect will not change when scrolling through the EFX selections, using the EFX SELECTOR (35) as instructed below to find a new effect. Adjusting the PARAMETER (37) rotary control setting will only change the engaged effect. In order to change the effect you must press the EFX ON/OFF (38) button to engage the next effect and adjust PARAMETER settings. - CUE MODE: For monitoring in your headphones without changing the PGM, press and hold the EFX ON/OFF (38) button until the button starts to blink slowly to indicate that the DSP effects are engaged in CUE mode. To disengage the CUE mode, press and hold the EFX ON/OFF (38) button until the EFX ON/OFF (38) stops blinking. To disengage the EFX in CUE mode, tap the EFX ON/OFF (38) button, and you will monitor the CUE without effects. The EFX ON/OFF (38) button begins blinking shortly indicating that the DSP effects are not engaged in CUE MODE. To engage the DSP, tap the EFX ON/OFF (38) button to engage the DSP EFX. 3. PARAMETER: To adjust the PARAMETER, or dynamics of the effect signal, use the PARAMETER (37) rotary knob to expand or minimize the effect level of the DSP effects. Rotate this knob clockwise to expand the effect. Rotate this knob counter clockwise to minimize the effect. When an effect has been engaged, you will notice that scanning through the effects selection will not change the effect. Adjusting the parameter setting will only change the engaged effect. Follow the EFX instructions to change the effect and then you may use the parameter control to adjust the parameter setting of the engaged effect. 4. LCD: The blue LCD (36) shows the EFX selection abbreviated name, to indicate which effect is activated or which effect may be activated at the top part of the screen. While the bottom part of the screen displays the PARAMETER level as controlled by the PARAMETER (37) rotary knob. 5. EFX SELECTOR: Use the EFX (35) rotary knob to scan through the 26 DSP effects as indicated in the blue LCD (36) display. Once you have found an effect you would like to engage, press the EFX ON/OFF (38) button to preview the DSP effect. The EFX (35) rotary control can rotate 360o while scanning through the effects. Rotate the EFX (35) knob clockwise to scan forward through the EFX list. Rotate the EFX (35) rotary control counterclockwise to scan backwards through the EFX list. The effects are listed on page 15. NOTE: WHEN SCROLLING THROUGH THE EFFECTS YOU WIL FIRST SEE THE NUMBER OF THE EFFECT, THEN THE LCD (36) WILL AUTOMATICALLY SWITCH THE VIEW TO THE PARAMETER SETTING. THIS WILL AID IN SCROLLING TO AN EFFECT QUICKLY BY FINDING THE NUMBER OF THE EFFECT. PMX-05 EFX SECTION: USER REPLACEABLE CROSS FADER 1. UNSCREW THE OUTSIDE MIXER FACE PLATE SCREWS AND REMOVE THE FACE PLATE. THEN REMOVE FADER PLATE SCREWS (B & C). 2. CAREFULLY LIFT THE FADER AND UNPLUG THE CABLE (D). 3. PLUG THE NEW FADER INTO THE CABLE AND PLACE IT BACK IN THE MIXER. 4. SCREW FADER PLATE TO THE MIXER AND REPLACE THE MIXER FACE PLATE. (6) INPUTS: DJ Mic................................................1.5 mV 1 kOhm Balanced Phono.................................................................3 mV 47 kOhm Line................................................................150 mV 10 kOhm OUTPUTS: Amp................................................................0 dB 1V 400 Ohm Max.............