Assessments - 6, GPA: 4
(
)
)
|
Facilidade de uso
Please take the time to fill in and return the warranty card within 14 days after the date of purchase, so as to benefit from our extended warranty. Or register online at 2. CONTROL ELEMENTS On the added view sheet you will find the corresponding illustrations for all control elements. The numbering of most of the control elements is the same for all three products. Because of the different design and some varying elements, the numbering is not always consistent. We therefore marked those differences adding a “V-AMPIRE only”, “V-AMP PRO only” or “V-AMP 2 only”. 2.1 Front panel/surface m Use the POWER switch to put the V-AMPIRE (rear) and the V-AMP PRO (front) into operation. The POWER switch should be in the “off’ position (not pressed) if you want to connect the device to the mains. Attention: The POWER switch does not fully disconnect the unit from the mains. Unplug the power cord completely when the unit is not used for prolonged periods of time. l~2~l The GAIN control determines the distortion level of an amp simulation. I~3~l The VOLUME control determines the volume of the selected preset. m The BASS control in the EQ section is for boosting or cutting the low-frequency range. m The MID control is for boosting or cutting the mid-range frequencies. nn TREBLE controls the high-frequency range of the selected preset. C The LED rings around the VOLUME, BASS, MID, TREBLE, GAIN, EFFECTS MIX and REVERB controls each have nine LEDs. On each ring either one LED or two neighboring LEDs (in between positon) will light up at a time, indicating a total of 17 different positions. If the TAP key 33] is down, the TREBLE control functions as a PRESENCE control. This enables you to boost/cut a high-frequency filter tuned to whatever amp model is active, thus simulating the frequency-dependent coupling of tube amps. m The AMPS control is for selecting one of 32 different amplifier simulation models. The control is surrounded by a ring of 16 LEDs. Each LED corresponds to two types of amplifier. The first 16 simulations can be selected by turning the AMPS control (V-AMP PRO/V-AMP 2: white, V-AMPIRE: black). To select the simulation models 17 - 32 (V-AMP PRO/ V-AMP 2: gray, V-AMPIRE: white), press down the TAP key while making your selection by turning the AMPS control. The LED “17 - 32” in the bottom left-hand corner of the DISPLAY indicates that one of the simulation models 17 - 32 has been selected. In addition, you can activate a PREAMP BYPASS by pressing the key combination TUNER |JL| and TAP [H. If PREAMP BYPASS has been selected, none of the LEDs on the AMPS control lights up. To disable PREAMP BYPASS, simply select a different amp model or press both keys again. lin These five keys are for selecting a preset (A - E) within one bank. In EDIT mode (activated by simultaneously pressing the arrow keys described in HO]), the keys perform the function printed directly above them: 2. CONTROL ELEMENTS S V-AMPIRE/V-AMP PRO/V-AMP 2 ▲ A: Accesses the MIDI functions. Use the arrow keys to set the MIDI channels (1 through 16) for transmitting and receiving MIDI data. If you use key A in EDIT mode to select the MIDI function and then press the TAP key, the MIDI OUT jack is set to act as a MIDI THRU. In this setting (the TAP LED is lit) no MIDI data is sent, but the device passes on the signal received at the MIDI IN jack. ▲ B: Selects the DRIVE function. This noticeably raises distortion and volume. Use the arrow keys to switch DRIVE on and off. The DRIVE function is wired pre GAIN control. While editing the DRIVE function, you can also activate and adjust the Wah-Wah effect by turning the EFFECTS control. The LEDs surrounding the EFFECTS control indicate the position of the pedal. If none of the LEDs lights up, the Wah-Wah is not acitvated. ▲ C: This key activates the CABINETS mode. Use the arrow keys to select the type of speaker or combination of speakers you want. You can also switch off the speaker simulation completely (“-”). For further details, please refer to chapter S.2. ▲ D: Use this key to select the REVERB function. The arrow keys can be used to select one of nine different types of reverb in addition to the multi-effects processor. For further details see chapter 6.3. ▲ E: Here you can activate the NOISE GATE function. Use the arrow keys to adjust the noise reduction threshold. After preset editing, please press TUNER/EXIT to quit (the EDIT MODE LED dies out). C DIGITAL OUT: The digital output (V-AMP PRO only) can be configured if keys A and B are pressed simultaneously. The display reads either “SP” for S/PDIF or “AE” for AES/EBU. Switch between these two formats using the TAP key. The LEDs in the display show whether you have chosen internal synchronization (with 44.1, 48 or 96 kHz sample rate) or external synchronization via word clock (see tab. 2.1 in this user’s manual). Use the arrow keys to select the appropriate sample rate with respect to the receiving devic...
Este manual também é adequado para os modelos :Instrumentos musicais - V-AMP 2 (1.62 mb)
Instrumentos musicais - V-AMPIRE (1.62 mb)