Assessments - 4, GPA: 3.8 ( )

Fabricante : JVC Arquivo Tamanho: 5.03 mb Arquivo Nome : Língua de Ensino:

Performing a second wipe transition runs in the reverse direction. • Disabled — Wipes always run in the direction specified in step 4 above. To change other wipe modifiers: 1. Press WIPE to access the Wipe menu. 2. Press NEXT to cycle through the available wipe modifiers. 3. Use the corresponding knob to change the following: •Pattern (Pattrn) — to find and select a desired pattern. • X Pos or Y Pos — to position the wipe pattern. • Aspect — to adjust the aspect ratio. • Border Size (Border) — to adjust the size of the border. • Image Softness (Soft) — to blur or harden the border. • Border color (these options only appear if you set the Border Size greater than 0.0%) › Use the Load knob to select a preset color. Press the Load knob to load the color. › Use the BHue, BSat, and BLum knobs until the desired color is achieved. • Rotation (Rot) — to rotate the pattern. •Horizontal (HMult) and Vertical (VMult) Multiplication — to create multiple instances of the pattern. Note: • You can select a pattern using the Pattern Buttons. This also displays the Wipe menu. • The X Pos and Y Pos can be adjusted using the positioner (KM-H 3000 only). • Aspect adjustments are not available for all patterns. • Circle, left square, right square, and diagonal patterns with aspect adjustments can not be rotated. Aux Buses The switcher has three timed Aux buses which have access to the following sources: • Any primary source (including Media-Store) • Program • Clean Feed •Preview • Chroma Key Alpha Accessing the Aux Buses KM-H3000: The Aux buses can be accessed from control panel buttons. KM-H2500: The Aux buses can be accessed through the menu system. To access Aux buses on the KM-H2500: These special sources are found on the first four buttons on the Preset bus. To select a special source for an Aux bus: 1 2 1 2 1. Press AUX SEL to display the Aux menu. 2. Select an Aux bus by pressing the corresponding knob. To access Aux buses on the KM-H3000: 1 1. Select the desired Aux bus by pressing AUX 1 - 3. Selecting a Source for the Aux Buses Once an Aux bus has been selected, you can change the source. To select a source for an Aux bus: 1. Select the Aux bus you wish to choose a source on. 2. Press the desired source button on the Key/Aux bus. Selecting a Special Source for the Aux Buses You can select the following special sources by selecting them on the Preset bus: • Program (AUX PGM) • Preview (AUX PV) • Clean Feed (AUX CLN) • Chroma Key Alpha (fourth source button) 1 3 2 1. Select the Aux bus you wish to choose a source on. 2. Press and hold SHIFT on the Key/Aux bus. 3. Press any of AUX PGM, AUX PV, AUX CLN, or the fourth source button (to access Chroma Key Alpha) on the Preset bus. Tallies The switcher has tally relays assigned to inputs as follows (pin 1 is the top right pin when looking at the Tally Port): 543219876 Figure 11 Tally Port Pin Input 1 1 2 3 3 5 4 7 5 Common Ground 6 2 7 4 8 6 9 8 When the corresponding input is on-air, the associated tally pin is closed, creating a contact closure. Note: • Tally wiring can be difficult. Consult with your facility engineer before undertaking any tally wiring. For More Information on... • port locations, refer to the section “Control Panel Rear Connections Overview” on page 2 General Purpose Interface (GPI) The switcher has 24 GPI inputs that are used to trigger memory recalls, transitions, and Aux bus input changes. The GPI inputs are assigned as follows (Pin 1 is the top right pin when looking at the GPI Port). 13121110987654321141516171819202122232425 Figure 12 GPI Port Pin Trigger 1 Dissolve Key 1 2 Dissolve Key 2 3 Dissolve Key 3 (KM-H 3000 only) 4 Perform Auto Transition 5 Perform Program / Preset Bus cut 6 Perform Key 1 cut 7 Perform Key 2 cut 8 Perform Key 3 cut (KM-H 3000 only) 9 Perform Fade-to-Black 10 Set Aux Bus 1 to Input 1 11 Set Aux Bus 1 to Input 2 12 Set Aux Bus 1 to Input 3 13 Set Aux Bus 1 to Input 4 14 Set Aux Bus 1 to Input 5 15 Recall Memory 0a 16 Recall Memory 1a 17 Recall Memory 2a 18 Recall Memory 3a 19 Recall Memory 4a 20 Recall Memory 5a 21 Recall Memory 6a 22 Recall Memory 7a 23 Recall Memory 8a 24 Recall Memory 9a 25 Ground a. Only memory registers from memory bank 0 can be recalled with a GPI trigger. For More Information on... • port locations, refer to the section “Control Panel Rear Connections Overview” on page 2 Editor Port The switcher has an Editor port that allows you to control your switcher from a device that supports the GVG100 editor protocol. The pinout is as follows: 543219876 Figure 13 Editor Port Pin Input 1 Not Connected 2 Tx 3 Rx+ 4 Ground 5 Ground 6 Not Connected 7 Tx+ Rx 8 9 Not Connected Supported Editors The following editors have been tested:: • Editware LE-2000 Series • Sony BVE-900/910 • Sony BVE-2000 For More Information on... • GVG100 protocol support, refer to the section “GVG100 Protocol Supported Commands” on page 44. • port locations, refer to the section “Control Panel Rear Connections Overview” on page 2 36 Media-Stor...

Baixe o seu

Para fazer o download, introduza 2 dígitos :