Assessments - 3, GPA: 3.7
(
)
)
|
Facilidade de uso
13, 2001 Normal mode Section 1. Receive data Channel Voice Messages * Following Channel Voice Messages can be recorded in SETUP/MIDI PART/ Part CH. Note Off Status 2nd byte 3rd byte 8nH kkH vvH 9nH kkH 00H n = MIDI channel number: 0H - FH (ch.1 - ch.16) kk = note number: 00H - 7FH (0 - 127) vv = note off velocity: 00H - 7FH (0 - 127) * Only the channel assigned to the backing part can be received. * The Velocity Values of Note Off message are ignored. * When recording, this is recorded in the sequencer data itself. Note On Status 2nd byte 3rd byte 9nH kkH vvH n = MIDI channel number: 0H - FH (ch.1 - ch.16) kk = note number: 00H - 7FH (0 - 127) vv = note on velocity: 00H - 7FH (0 - 127) * A channel which is assigned to the drum kit part will receive only the note numbers which are specified by the drum kit. * A channel which is assigned to the percussion part will receive only the note numbers which are specified by the percussion set. * When recording, this is recorded in the sequencer data itself. Polyphonic Key Pressure Status 2nd byte 3rd byte AnH kkH vvH n = MIDI channel number: 0H - FH (ch.1 - ch.16) kk = note number: 00H - 7FH (0 - 127) vv = Value: 00H - 7FH (0 - 127) * A channel which is assigned to the drum kit part will receive only the note numbers which are specified by the drum kit. * If the value is greater than 40H (64), the decay of the note sounded by the received note number will be shortened. * Not recorded in the sequencer. Control Change . Bank Select (Controller number 0, 32) Status 2nd byte 3rd byte BnH 00H mmH BnH 20H llH n = MIDI channel number: 0H - FH (ch.1 - ch.16) mm = Bank number MSB: 00H - 7FH (bank.1 - bank.128) ll = Bank number LSB: processed as 00H * Not Received when SETUP/MIDI COMMON/Rx PC Sw is set to "OFF".(Initial Value is ON) * Bank select processing will be suspended until a program change message is received. * Only the channel assigned to the backing part can be received. * Not recorded in the sequencer. . Foot Control (Controller number 4) Status 2nd byte 3rd byte BnH 04H vvH n = MIDI channel number: 0H - FH (ch.1 - ch.16) vv = Control value: 00H - 7FH (0 - 127) * Only the channel assigned to the drum kit part can be received. * When recording, this will be recorded as PEDAL CC data in the sequencer data itself. . Data Entry (Controller number 6) Status 2nd byte 3rd byte BnH 06H mmH n = MIDI channel number: 0H - FH (ch.1 - ch.16) mm = The value of the parameter specified by RPN. * Only the channel assigned to the backing part can be received. * Not recorded in the sequencer. On the normal mode of TD-6, RPN can be used to modify the following parameters. RPN Data entry MSB LSB MSB LSB 00H 00H mmH -- 7FH 7FH --- -- Explanation Pitch Bend Sensitivity mm: 00H - 18H (0 - 24 semitones) LSB: ignored (processed as 00H) specify up to 2 octaves in semitone steps RPN null set condition where RPN is unspecified. The data entry messages after set RPN null will be ignored.(No Data entry messages are required after RPN null). Settings already made will not change. MSB,LSB of data entry:ignored . Volume (Controller number 7) Status 2nd byte 3rd byte BnH 07H vvH n = MIDI channel number: 0H - FH (ch.1 - ch.16) vv = Volume: 00H - 7FH (0 - 127) * Volume messages are used to adjust the volume balance of each part. * Only the channel assigned to the percussion part and the backing part can be received. * Not recorded in the sequencer. . Pan (Controller number 10) Status 2nd byte 3rd byte BnH 0AH vvH n = MIDI channel number: 0H - FH (ch.1 - ch.16) vv = Pan: 00H - 40H - 7FH (Left - Center - Right) * Only the channel assigned to the backing part can be received. * Not recorded in the sequencer. . Hold 1 (Controller number 64) Status 2nd byte 3rd byte BnH 40H vvH n = MIDI channel number: 0H - FH (ch.1 - ch.16) vv = Control value: 00H - 7FH (0 - 127) 0-63 = OFF, 64-127 = ON * Only the channel assigned to the backing part can be received. * When recording, this is recorded in the sequencer data itself. Anhang 135 MIDI-Implementation MIDI-Implementation . Effect 1(Reverb Send Level) (Controller number 91) Status 2nd byte 3rd byte BnH 5BH vvH n = MIDI channel number: 0H - FH (ch.1 - ch.16) vv = Reverb send level: 00H - 7FH (0 - 127) * Only the channel assigned to the backing part can be received. * When recording, this is recorded in the sequencer data itself. . RPN MSB/LSB (Controller number 101, 100) Status 2nd byte 3rd byte BnH 65H mmH BnH 64H llH n = MIDI channel number:0H - FH (ch.1 - ch.16) mm = upper byte of parameter number specified by RPN (MSB) ll = lower byte of parameter number specified by RPN (LSB) * Only the channel assigned to the backing part can be received. * The value specified by RPN will not be reset even by messages such as program change or reset all controllers. * When recording, this is recorded in the sequencer data itself. **RPN** The RPN (Registered Parameter Number) messages are expanded control changes,and each function of an RPN is described by the MIDI Sta...