Assessments - 2, GPA: 4
(
)
)
|
por este dispositivo também tem outras instruções :
Facilidade de uso
“Storing Settings (Write Operation)” (p. 16) SELECT button Provides for selection among MANUAL and MEMORY 1–4. MEMORY Pedals (MEMORY Ў/^) These perform two functions, selecting among MANUAL and MEMORY 1–4, and anti-feedback. “MEMORY Ў/^ Pedal Functions” (p. 14) “How to Use the ANTI-FEEDBACK” (p. 19) Part Names and Functions ON/OFF pedal ON/OFF indicator The effects are alternately switched on and off each time this pedal is pressed. The ON/OFF indicator lights when the effects are on. ON: Sounds set using the AD-8 are output. OFF: Sounds are output exactly as input (Bypass) or muted (Mute). “ON/OFF Pedal Operation” ( Part Names and Functions ON/OFF pedal ON/OFF indicator The effects are alternately switched on and off each time this pedal is pressed. The ON/OFF indicator lights when the effects are on. ON: Sounds set using the AD-8 are output. OFF: Sounds are output exactly as input (Bypass) or muted (Mute). “ON/OFF Pedal Operation” (p. 14) “Setting the Function Used When the Effects Are Off (Bypass/Mute)” (p. 17) TUNER TUNER meter This shows the difference between the note indicated in the tuner display and the pitch of the sound being input while the tuner is operating. TUNER display This indicates the note names when the tuner is operating. “How to Use the Tuner” (p. 18) * Settings values and other information is displayed here when the tuner is not active. PITCH button This sets the tuner’s reference pitch. “Changing the Reference Pitch (PITCH)” (p. 18) BYPASS/MUTE button This sets whether the AD-8 switches to Bypass or Mute mode when the effects are switched off with the ON/OFF pedal. “Setting the Function Used When the Effects Are Off (Bypass/Mute)” (p. 17) ANTI-FEEDBACK indicator Indicates the status of the anti-feedback function. “How to Use the ANTI-FEEDBACK” (p. 19) Flashing: Detection of feedback frequencies in progress Lit solidly: On Unlit: Off Part Names and Functions Rear Panel PHONES jack You can connect headphones here to listen to the sounds. * Connect headphones only after turning on the power. Also be sure to disconnect the headphones before turning off the power. INPUT jack Connect the output from your acoustic guitar or effects processor here. “Connections” (p. 6) * The AD-8 is switched on when a plug is connected to the INPUT jack. The power is turned off when the plug is disconnected from the jack. Be sure to disconnect any plug from this jack whenever the AD-8 is not in use. AC Adaptor jack This jack is used for connecting an optional AC adaptor (the PSA series). Using the AC adaptor allows you to perform with the AD-8 for extended periods without having to worry about running out of battery power. ELECTRIC GUITAR AMP OUTPUT jack This jack is used for connecting to electric guitar amps. “Connecting to Electric Guitar Amps” (p. 8) UNBALANCED OUTPUT A (MONO)/B jacks These jacks are used for connecting to acoustic guitar amps, multitrack recorders, and other such equipment. When using monaural signals, connect to the UNBALANCED OUTPUT A (MONO) jack. “Connecting to Acoustic Guitar Amps or Multitrack Recorders” (p. 7) BALANCED OUTPUT A/B jacks Use these jacks to connect to a mixer. “Connecting to Mixers” (p. 6) STEREO/MONO switch This switches between stereo output (STEREO) and monaural output (MONO). The same sounds are output from A and B when mono output is used. NOR/LIFT switch This disconnects the 1:GND pin from the input’s ground. Switch this to “LIFT” if humming or other noise from ground loops becomes a problem. The AD-8 is normally used with this set to NOR. Cord Hook Wrap the cable around this hook so that the AC adaptor cable is not pulled out accidentally “Connections” (p. 6). Security slot ( ) Operation ON/OFF Pedal Operation The ON/OFF pedal is set to “ON” when the power is turned on. This turns the AD-8’s effects on and off. The ON/OFF indicator lights up when the effect is on. When the effects are switched off, the input sounds are output as is (when set to the factory settings); the tuner is also operational. You can also mute the output when the effects are turned off. “Setting the Function Used When the Effects Are Off (Bypass/Mute)” (p. 17) On: Lit Off: Unlit MEMORY Ў/^ Pedal Functions These pedals allow you select among MANUAL mode and MEMORY 1–4. MANUAL: The sound as determined by the settings of the panel's knobs is output. MEMORY: Sounds conforming to pre-programmed settings are output. Press the MEMORY ^ pedal to switch through the memories in the following sequence: MANUAL >MEMORY 1 >MEMORY 2 >MEMORY 3 > MEMORY 4 > MANUAL. Press the MEMORY Ў pedal to switch through the memories in the following sequence: MANUAL >MEMORY 4 >MEMORY 3 >MEMORY 2 > MEMORY 1 > MANUAL. You can also use the MEMORY Ў/^ pedals when using the anti-feedback function. “How to Use the ANTI-FEEDBACK” (p. 19) Operation Panel Operation So that you will be better able to follow along with the instructions in this document, first press the ON/OFF pedal so that the effects...