Assessments - 1, GPA: 4
(
)
)
|
Facilidade de uso
Also incorporated Noise Reduction Circuit produce the high quality sounds. Equipped with LED indicator for display of Effect On/Off. NAME AND FUNCTIONS BATTERY •- ELIMINATOR JACK INDICATOR REPEAT RATE OUTPUT JACK PEDAL SWITCH ECHO REPEAT HATE INTENSITY #ÖÜT INPUT# '......' Delay -•INTENSITY # ECHO VOLUME INPUT JACK THUMBSCREW REPEAT RATE This knob controls the repetition rate of the echos. INTENSITY This knob controls the intensity of the returning echo. Turning this knob clockwise increase the repetition rate of the echo, fully turning this knob counterclockwise becomes Single Delay. *When this knob is too turning clockwise, thus feedback occurs. Feedback is desirable for certain type of Special effects. ECHO VOLUME This knob controls the output level of the echo. Turning this knob clockwise increase the level of the delayed sound, fully turning this knob counterclockwise produce only normal sound. INPUT JACK The unit is powered-on by plug-in to the input jack. Keep the plug out from the jack when not in use. OUTPUT JACK The DM-2's low impedance output to the amplifiers is offered to ensure low noise and hum. BATTERY ELIMINATOR JACK The BOSS AC Adaptor is connected to the Battery Eliminator jack when battery operation is not necessarily the most desirable situation. INDICATOR By the LED indicator you can see whether the unit is on or off, even in the darkest on-stage situation. This indicator also allows you to check the battery. When the time comes to replace the battery, the indicator fails to light or becomes dimmer. PEDAL SWITCH in our unique FET switching system there are no mechanical contents in the signal system so it won't make an audible click, and it can't make a pop. The switching totally electronically and therefore, cleanly. THUMB SCREW The battery sits in a special compertment under the same footswitch plate that activates the silent switch. When the time comes to replace the battery, you don't even need tools. *Do not remove off the screw from the unit. BEFORE USING DM 2 *When operating DM-2 from AC line, use BOSS AC Adaptor for DM-2. CONNECTING DM-2 r AMPLIFIER Avoid using DM-2 in very dusty location or under high temperature or humidity conditions. BOSS AC ADAPTOR ACA 100 TO BATTERY ELIMINATOR JACK LEAD GUITAR Power is switched on while a plug is BOSS DM-2 into input jack. BASS GUITAR im» KEYBOARD (Unplug this unit when it is not to be used. Be sure to take off connecting plug from Input jack) OPERATING DM-2 1 2 IT ^Jiiïrfewsiü# ...... After connecting all cords required, set all knobs on the panel as illustrated. ÉI'- O INTENSITY ■ Depress the pedal switch. Check LED lights to indicate “EFFECT ON" and extinguishes to indicate "EFFECT OFF". #This check LED is also used to check battery. If LED fails to light or becomes dim, the battery should be replaced. Turn REPEAT RATE control to proper position. Adjust the repetition rate by setting the knob of intensity to proper position. (note: When this knob is too turning clockwise, thus feedback occurs.) Turn ECHO knob to proper position. CAUTIONS •When you don't use for a long period, remove the battery to prevent current leakage and leaking out of sticky sub* stance. •If battery voltage drops, effect becomes inferior or no sound is produced. To prevent that, replace the battery a little earlier. AC ADAPTOR (OPTION) BOSS АСА 120 BOSS АСА 240 FOR 117V AC FOR 240V AC •Be sure to keep the battery snapped by connector into the housing, when using AC adaptor, too. *Even if AC Adaptor cord comes out during performance, operations immediately changes to battery, causing no trouble in continued performance. •Power is switched on while a plug is put into input jack. When you do not use, keep the plug off the jack. Use BOSS AC adaptor for AC operation. Use of different adaptors may cause improper operation or no sound. BOSS ACA 220 FOR 220V AC CAUTIONS FOR REPLACING AND HANDLING BATTERY 9V BATTERY BATTERY CONNECTOR BATTERY STRAP PEDAL (COVER) SCREW SPRING BASE COIL SPRING PEDAL GUIDE BATTERY HOUSING REPLACING BATTERY USE ONE 9-VOLT BATTERY. OLoosen the screw of pedal to open it and take out battery from its housing. OReplace the battery by a fresh one and put it into position. ©Set coil spring onto the projection on the rear of the pedal and shut the cover (pedal). Finally, insert the screw into the pedal guide and tighten it. At this time, be careful not to catch the battery strap in the cover or coil spring. [^Roland® 10405 UPC 10M6 SPECIFICATIONS Power.................Battery 9V{1), AC Adapter Current draw............11 mA at 9V Controls...............REPEAT RATE, INTENSITY, ECHO VOLUME Others................Normal/Effect Changeover Switch, Indicator Jacks.................Input, Output, AC Adapter Delay time..............20ms ~ 300ms Residual noise.................Less than-100dBm (IHF-A) Input impedance..............470kn Output load imp...