Assessments - 3, GPA: 4
(
)
)
|
Facilidade de uso
Note on Status 2nd byte 3rd byte 9nH kkH vvH n=MIDI channel number: 0H - FH (ch.1 - ch.16) kk=note number: 00H - 7FH (0 - 127) vv=note on velocity: 01H - 7FH (1 - 127) * Note numbers outside the range of 15-113 are transposed to the nearest octave within this range. * Transpose function does not affect the recognized note numbers. Control Change * The value specified by a Control Change message will not be reset even by a Program Change, etc. .Data Entry (Controller number 6,38) Status 2nd byte 3rd byte BnH 06H mmH BnH 26H llH n=MIDI channel number: 0H - FH (ch.1 - ch.16) mm,ll= the value of the parameter specified by RPN mm=MSB, ll=LSB .Volume (Controller number 7) Status 2nd byte 3rd byte BnH 07H vvH n=MIDI channel number: 0H - FH (ch.1 - ch.16) vv=Volume: 00H - 7FH (0 - 127) * Received volume messages affect received note event levels (Rx ch/Part), and cannot affect internal keyboard notes. .Expression (Controller number 11) Status 2nd byte 3rd byte BnH 0BH vvH n=MIDI channel number: 0H - FH (ch.1 - ch.16) vv=Expression: 00H - 7FH (0 - 127) * These message can affect only MIDI notes. .Hold 1 (Controller number 64) Status 2nd byte 3rd byte BnH 40H vvH n=MIDI channel number: 0H - FH (ch.1 - ch.16) vv=Control value: 00H - 7FH (0 - 127) 0-63=OFF, 64-127=ON * These message can affect only MIDI notes. .Sostenuto (Controller number 66) Status 2nd byte 3rd byte BnH 42H vvH n=MIDI channel number: 0H - FH (ch.1 - ch.16) vv=Control value: 00H - 7FH (0 - 127) 0-63=OFF, 64-127=ON * These message can affect only MIDI notes. .Soft (Controller number 67) Status 2nd byte 3rd byte BnH 43H vvH n=MIDI channel number: 0H - FH (ch.1 - ch.16) vv=Control value: 00H - 7FH (0 - 127) 0-63=OFF, 64-127=ON * These message can affect only MIDI notes. .Effect 1 (Reverb Send Level) (Controller number 91) Status 2nd byte 3rd byte BnH 5BH vvH n=MIDI channel number: 0H - FH (ch.1 - ch.16) vv=Control value: 00H - 7FH (0 - 127) 0-63=OFF 64-127=ON .Effect 3 (Chorus Send Level) (Controller number 93) Status 2nd byte 3rd byte BnH 5DH vvH n=MIDI channel number: 0H - FH (ch.1 - ch.16) vv=Control value: 00H - 7FH (0 - 127) 0-63=OFF 64-127=ON .RPN MSB/LSB (Controller number 100,101) Status 2nd byte 3rd byte BnH 65H mmH BnH 64H llH n=MIDI channel number: 0H - FH (ch.1 - ch.16) mm=upper byte of parameter number specified by RPN ll=lower byte of parameter number specified by RPN * The value specified by RPN will not be reset even by messages such as Program Change or Reset All Controller. ** RPN ** The RPN (Registered Parameter Number) messages are expanded control changes, and each function of an RPN is described by the MIDI Standard. To use these messages, you must first use RPN MSB and RPN LSB messages to specify the parameter to be controlled, and then use Data Entry messages to specify the value of the specified parameter. Once an RPN parameter has been specified, all Data Entry messages received on that channel will modify the value of that parameter. To prevent accidents, it is recommended that you set RPN Null (RPN Number = 7FH/7FH) when you have finished setting the value of the desired parameter. On the ep-70/90, RPN can be used to modify the following parameters. RPN Data entry MSB LSB MSB LSB Explanation 00H 01H mmH llH Master Fine Tuning mm,ll: 00 00H - 40 00H - 7F 7FH (-100 - 0 - +99.9 cents) 7FH 7FH --- ---RPN null Set condition where RPN is unspecified. Settings already made will not change. mm,ll: ignored Copyright © 1999 ROLAND CORPORATION All rights reserved. No part of this publication may be reproduced in any form without the written permission of ROLAND CORPORATION. Program Change Status 2nd byte CnH ppH n=MIDI channel number: 0H - FH (ch.1 - ch.16) pp=Program number: 00H - 23H (prog.1 - 36) Received program change message are assigned as follows. program number tone 1 Piano1 2 Piano2 3 E.Piano 4 Vibraphone 5 Harpsichord 6 Organ 7 Strings 8 Choir 9 Piano1 + Piano2 10 Piano1 + E.Piano 11 Piano1 + Vibraphone 12 Piano1 + Harpsichord 13 Piano1 + Organ 14 Piano1 + Strings 15 Piano1 + Choir 16 Piano2 + E.Piano 17 Piano2 + Vibraphone 18 Piano2 + Harpsichord 19 Piano2 + Organ 20 Piano2 + Strings 21 Piano2 + Choir 22 E.Piano + Vibraphone 23 E.Piano + Harpsichord 24 E.Piano + Organ 25 E.Piano + Strings 26 E.Piano + Choir 27 Vibraphone + Harpsichord 28 Vibraphone + Organ 29 Vibraphone + Strings 30 Vibraphone + Choir 31 Harpsichord + Organ 32 Harpsichord + Strings 33 Harpsichord + Choir 34 Organ + Strings 35 Organ + Choir 36 Strings + Choir * 9-36 are in Dual Play mode. * Any other program number will be ignored. * After a Program Change message is received, the sound will change beginning with the next Note-on. Voices already sounding when the Program Change message was received will not be affected. Channel Mode Messages Reset All Controllers (Controller number 121) Status 2nd byte 3rd byte BnH 79H 00H n=MIDI channel number: 0H - FH (ch.1 - ch.16) * When this message is received, the following controllers will be set to their reset values....