Assessments - 4, GPA: 4
(
)
)
|
por este dispositivo também tem outras instruções :
Facilidade de uso
Red On Red/Green Blinking On 2 Tap the FDR-1’ s pedal switch in timing with the tempo. Red On 3 Press and hold the FDR-1’ s pedal switch for at least two seconds. The rate is stored. Effect Pedal Switch Rate Setting Off On Off> Rate confirmed * Vibrato rate for use with the tempo settings can be made in the range * If you carry out Step 3 immediately after Step 2, Step 3 may inadvertently changing the RATE setting. Allow a brief interval to pass before progressing * You can also set the rate by turning the VIBRATO knob while depressing p. 11). When you’ve finished setting the rate, release the pedal switch, then depress it again, holding Changing Changing * The use of an AC adaptor is recommended unit’s power consumption is relatively you prefer to use a battery, please use Pedal Spring Base Cord Coil Spring Guide Bush Hole Battery Snap Thumbscrew Battery Housing Battery Snap 9V Battery 1. Hold down thumbscrew, then upward. * The pedal can be opened without thumbscrew completely. 2. Remove the old battery from housing, and remove the snap to it. 3. Connect the snap cord to the new battery, and place the battery inside the battery housing. * Be sure to carefully observe the battery’s polarity (+ versus -). 4. Slip the coil spring onto the spring base on the back of the pedal, and then close the pedal. * Carefully avoid getting the snap cord caught in the pedal, coil spring, and battery housing. 5. Finally, insert the thumbscrew into the guide bush hole and fasten it securely. Troubleshooting Troubleshooting . Is the specified sold separately) properly Check the AC adaptor p. 7, p. 8). * Never use any AC adapter other for use with the FDR-1. . Is the battery low or dead? Replace it with a new battery ( p. 14). * The battery that is supplied with the unit is temporary use, intended primarily for testing pedal’s operation. * The use of an AC adaptor is recommended as the unit’s power consumption is relatively high. Should you prefer to use a battery, please use the alkaline type. * To prevent unnecessary battery consumption, be sure to disconnect the plug from the INPUT jack when not using the effects unit ( p. 5) . . Is your guitar properly connected to the INPUT jack? Check the connection once more ( p. 7, p. 8). * The power is switched on only when a cable is plugged in to the * The CHECK indicator being applied or not. the power to the device No sound / low volume . Is your instrument properly to the FDR-1? Check the connection once more p. 7, p. 8). . Is the LEVEL knob set too low? The further counterclockwise you turn LEVEL knob, the more the volume is reduced when the effect is on. Turn the LEVEL knob clockwise to increase the volume. . Is the volume turned down on any guitar amp or effects device you have connected? Check the settings of the connected device. . Is the battery low or dead? Replace it with a new battery ( p. 14). Effect won’t turn off . Could you be in the vibrato rate setting mode ( p. 12, p. 13)? 16 Setting Samples Standard Crunch Sound fig.FDR-1-sample1.eps Hard Overdrive Sound fig.FDR-1-sample1.eps Surf Rock Sound fig.FDR-1-sample1.eps Vibrato Sound fig.FDR-1-sample1.eps For details about the vibrato rate, please refer to p. 12, p. 13. Setting Setting Setting Setting Specifications Specifications Nominal Input ....................... -20 dBu Input Impedance: .............................. 1 M. Nominal Output Level: .................... -20 dBu Output Impedance: .......................... 2.2 k. Recommended Load Impedance: ... 10 k. or greater Controls: ............................................. Pedal switch, GAIN knob, LEVEL BASS knob, REVERB knob, VIBRATO Indicators: ............................................. CHECK indicator (for effect on/off status Connectors: ........................................ INPUT jack, OUTPUT jack, AC adaptor Power Supply: ................................... DC 9 V: Dry battery 6F22 (9 V) type (carbon)/ Dry battery 6LR61 (9 V) type (alkaline) AC Adaptor (PSA-series: optional) Current Draw: ................................... 40 mA (DC 9 V) * Expected battery life under continuous use: Carbon: 2.7 hours, Alkaline: 9 hours These figures will vary depending on the actual conditions of use. Dimensions: ....................................... 73 (W) x 129 (D) x 59 (H) mm / 2-7/8 (W) x 5-1/8 (D) x 2-3/8 (H) inches Specifications Specifications ) Accessories......................................... Owner’s manual, “IMPORTANT NOTES,” dry battery/9 V type * The battery that is supplied use, intended primarily for testing We suggest replacing this with Option ................................................ AC adaptor (PSA-series) * 0 dBu = 0.775 Vrms * In the interest of product improvement, the specifications without prior notice. * Fender ® and DELUXE REVERB ® are the trademarks of FMIC. All rights reserved. * All product names mentioned in this document are trademarks of their respective owners. In this document, their names are used equipment whose sound...