Assessments - 3, GPA: 3.7
(
)
)
|
Facilidade de uso
See below for how to transmit the settings back to the FR-3 at a later stage. Sending Bulk data (back) to the FR-3 The FR-3 not only sends SysEx data to external devices (see above), it also receives them. (1) Connect the FR-3’s MIDI socket to the sequencer’s/ computer’s MIDI OUT socket. See page 45 for a connection diagram. Note: Your computer needs to be equipped with (or connected to) an appropriate MIDI interface. (2) Set the “MId” parameter (page 48) to “In”. (3) If you are working with a computer, launch the sequencer program. (4) Load the song that contains the data you want to transmit. (5) On your sequencer, perform all necessary actions to ensure that it transmits SysEx data. See its manual for details. Note: Be aware that by proceeding, you replace all internal settings. (6) Start playback of the data file or song on your sequencer, etc. Note: Wait until the “don” message appears before stopping playback on your sequencer. Failure to do so will render your FR-3 inoperable. If that happens, you need to initialize it (see “Restoring the factory defaults” on p. 53). (7) Stop playback of your sequencer. 7. Restoring the factory defaults You can reset the FR-3 to its factory settings, which means that your own Global settings are replaced by the settings the FR-3 contained when you first got it. You may wish to archive your settings before initializing the FR-3 (see p. 52). (1) Switch on the FR-3 while holding down the [SET] When all settings have been initialized, the display briefly shows the following message: and [ORCHESTRA] registers. don The FR-3 now again sounds and behaves like when you first bought it. The display changes to: Fty 53 Using optional batteries | Using optional batteries 54 r FR-3s/FR-3/FR-3sb/FR-3b V-Accordion 8. Using optional batteries Your FR-3 has a compartment that contains a special holder unit into which you can install 10 optional AA-type batteries. You can therefore play your instrument without connecting the supplied adapter. What can you do with batteries? • After installing optional batteries, the FR-3s/FR-3sb (where the “s” stands for “speakers”) can be used like an acoustic accordion – without any connection whatsoever. • FR-3s/FR-3sb and FR-3/FR-3b: If you use an optional wireless system, you don’t need audio cables that run from the FR-3 to your amplifier or mixing console. • FR-3s/FR-3sb and FR-3/FR-3b: If you use headphones, you can play just about anywhere. Note: Though it is perfectly possible to use rechargeable batteries, be aware that they cannot be recharged simply by leaving them in the FR-3’s compartment and connecting the adapter. You will need an external charging unit. Installing and removing batteries The FR-3 provides a battery compartment with a special holder unit into which 10 AA-type (R6) batteries can be installed. • Be sure to dispose of used batteries in accordance with local regulations. • First, read the precautions on page 10 and following. • New (or fully recharged) batteries should last about 2.5 hours (FR-3s/FR-3sb) or ±5 hours (FR-3/FR-3b) under continuous use. • Slightly before the batteries are fully exhausted, the following message appears. Note: The FR-3 contains an energy saving function that switches off the instrument when it is left unattended for more than 10 minutes. You may therefore have to switch it on again from time to time. (1) Switch off the FR-3. (2) Remove the cushion located between the Treble keyboard and the bellows. (3) Remove the cover from the FR-3’s battery compartment by pressing the two tabs and lifting the cover. You should now see a tab that allows you to remove the battery case: General remarks about batteries bat (FR-3s/FR-3) (FR-3sb/FR-3b) Note about rechargeable batteries V-Accordion r Note about rechargeable batteries V-Accordion r (4) Use the tab to pull the battery case out of the compartment and turn the case around. The battery case is connected to the FR-3 by means of a cable with a padded connector strip. You can disconnect the cable from the battery case by pulling off the padded connector strip. Note that this install (or remove) the batteries without disconnecting the strip (5) Insert 10 AA-type (R6) batteries into the compartment (5 on either side), taking care to orient them in accordance with the “+” and “–” indications. (6) Insert the case with the 10 batteries into the compartment. (7) Close the FR-3’s battery compartment and reinstall the cushion. Note about rechargeable batteries Certain batteries can be recharged several times before they need to be replaced with a new ones. Note that it is normal for the battery to last increasingly shorter as time goes by. At the end of its life cycle, it may only last one hour, for example. But that is a gradual process. 55 FR-3s/FR-3/FR-3sb/FR-3b V-Accordion Troubleshooting | Troubleshooting 9. Troubleshooting This section provides an overview of points to check and actions to take when the FR-3 does not function as you expect. Feel free to conta...