Assessments - 5, GPA: 4.2
(
)
)
|
Facilidade de uso
You can initialize all settings, or only a specified section of the Patch data in the User area or Utility settings. The following types of data can be initialized. Display Data that is initialized System Utility parameters FX Set Effect Setting, Pedal Setting and Control Assign Setting data stored in the User. #1-1-1 -#4-5-5 The setting contents of Patches UG1-1- 1 - UG4-5-5 (Procedure) 3,4 jl M I r~l □ CD CZI CD CD ¡CD CD □ CD CD CD CD CD cn CD C=3 o m m 3,4 1 Turn off the power. 2 While holding [MOD] and [FEEDBACKER/SLOW GEAR] down, switch on the unit. A display will appear, allowing you to specify the area of data you wish to initialize. * If you decide not to initialize the settings, press [EXIT]. Initialization will be canceled, and the normal power-on display will appear. Fact .nry Preset Systeo + #4-5-5 Starting Point Ending Point 3 Move the cursor to “Starting Point” with [PARAMETER], then use the VALUE dial to get the display to show the data that is the beginning point of the initialization. 4 Move the cursor to “Ending Point” with [PARAMETER], then get the display to show the ending point of the initialization, also using the VALUE dial. 5 Press [WRITE], and the specified area of data will be initialized. The GT-5 will then be in its normal power-on state. 70 Troubleshooting If there is no sound or other operational problems occur, first check through the following solutions. If this does not resolve the problem, then contact your dealer or a nearby Roland service station. No Sound / Volume Too Low_ Are the connection cables broken? Try using a different set of connection cables. Is the GT-5 correctly connected to the other devices? Check connections with the other devices (page 10). Is the connected amp/mixer turned off, or the volume lowered? Check the settings of your amp/mixer system. Is the INPUT VOLUME knob lowered? Adjust the INPUT VOLUME knob to an appropriate position (page 11). Is the OUTPUT Level knob lowered? Adjust the OUTPUT Level knob to an appropriate position (page 12). Is Tuner/Bypass set to On? When the volume is set to "MUTE" in the Tuner/Bypass mode, even the direct sound will not be output by setting the Tuner/Bypass to "On" (page 16). Is each effect set correctly? Use the "Meter function" (page 30) to check the output level of each effect. If there is an effect for which the meter does not move, check the setti ngs for that effect (page 21). Is "Master Level" specified as a control assign Target? Move the controller to which it is assigned. Sound Is Distorted (the overload indicator lights frequently) Have you adjusted the input volume knob? Adjust the INPUT VOLUME knob to an appropriate setting (page 11). Even though you have set an effect to ON, the Effect Select button goes out and the effect gets switched OFF after a Write procedure has completed._ If Assign Hold (page 33) has been set to ON, the ON/OFF status of the effect set for the target of the Control Assign (page 24) will take on the value of the source, so it may differ from the status before the Write procedure. To solve this, you can either set Assign Hold to OFF or select Assign OFF for the relevant Control Assign. Patch Number Does Not Change____ Is something other than the Play page (page 11) shown in the display? On the GT-5, Patches can be selected only when the Play page is displayed. Press [EXIT] to return to the Play page. Parameters Specified with Control Assign Can’t Be Controlled_ When using the expression pedal When using the control pedal Check that the effect that includes the parameter to be controlled is set to Effect On. When a foot switch is connected to the EXP/CTL jack Make sure that the function of the jack to which the foot switch is assigned is set to "Assignable" (page 30). When using MIDI to control parameters Make sure that the MIDI channels of both devices match (page 58). Make sure that the controller numbers you are using match (page 24). MIDI Messages Are Not Received_ Are the MIDI cables broken? Try another set of MIDI cables. Is the GT-5 correctly connected to the other MIDI device? Check connections with the other MIDI device. Do the MIDI channel settings of both devices match? Make sure that the MIDI channels of both devices match (page 58). When you send messages from the GT-5, make sure the GT- 5 is set to the settings appropriate for sending data. Check the On/Off status for transmission of Program Change messages and the settings for the Controller Numbers to be transmitted (page 58). Section 5 Appendix 71 GUITAR EFFECTS PROCESSOR Date : May 24,1996 Model GT-5 MIDIImplementation Chart version: 1.00 Function... Transmitted Recognized Remarks Basic Channel Default Changed 1 — 16 1 — 16 1 — 16 1 —16 Memorized Mode Default Messages Altered X X OMNI ON/OFF X X Memorized Note Number : True Voice X ************** X Velocity Note ON Note OFF X X 0 '1 X After Touch Key’s Ch's X X X X Pitch Bend ...