Assessments - 2, GPA: 3.5
(
)
)
|
Facilidade de uso
4 (including a spring washer and a nut for each leg) • Exclusive wrench ......... 1 1. Turn the seat over and put it on a sturdy place. 2. Insert the bolt on the leg into the hole of the metal fitting of the seat (one at each of the four corners), and fit the spring washer then the nut onto the bolt. Use the exclusive wrench to tighten the nut securely. 3. After you have finished assembling the chair. Turn it over for normal usage. If there is looseness, loosen the nuts for adjustment and then retighten them securely. Note: When the nuts become loose while you are using the chair, use the exclusive wrench to retighten the nuts firmly. 4. Rotate the height adjusting handle to the right or left so you 3 How to assemble the Roland HP-7700 piano Assembly should be carried out by three people or more. The piano and stand are heavy. Take sufficient care in handling them. Install the piano in a location which is level and stable. ■ Check the parts Before you begin assembly, check that you have all the following parts. ® Stands (legs).................................................3 ® Pedal stand...................................................1 © Pedal stays...................................................2 ® Insulators......................................................3 @ Supporting boards.........................................2 ® Bolts Hex socket head cap bolts (M12X50)......8 Spring washers.........................................8 Plain washers............................................8 © Screws (M4X25)..........................................4 @ Hex wrench...................................................1 © Phillips/slotted screwdriver............................1 ■ Assembly procedure 1 Attach the stands (legs) to the piano. -1" ¡I> Assemble the supporting boards (§>, and place the piano on them. - Position the stands ® in place beneath the piano. ■t Using the bolts ®, fasten the stands ® to the piano. Tighten the bolts firmly with the hex wrenched. 2 Attach the pedal stand, and plug in the pedal cord and the power cord. 41 While lifting up the piano slightly, remove the supporting boards®. (This must be done by three people or more.) ■S' Using the bolts ®, fasten the pedal stand to the piano. Tighten the bolts firmly with the hex wrenched. 6) Using the screws ©, fasten the pedal stays to both the piano and the pedal stand. < 7) Place the insulators @ beneath the casters of the stands. ;|j Plug the pedal cord and the power cord into the respective sockets located on the bottom center of the piano. Note: When installing the piano in its location, be sure not to pinch the power cord underneath the piano. 4 Important notes [Placement] • The instrument is quite heavy and requires at least two people to move safely. Always take care not to damage the piano's finish. • Always first make sure that the location in which you intend to place the instrument is level. With the HP-7700, you will probably wish to have it secured in place while also protecting the floor where it stands. For this purpose, a set of Insulator are supplied, whitch should be placed under the caster wheels. • Avoid placing the instrument in direct sunlight or near a heater/air conditioner, all of which can damage the instrument's finish. • Electronic instruments can interfere with radio and television reception. If interference occurs, move the receiver or instrument to a different location. • Do not use the piano on the same power circuit with any device that will generate line noise; an electric motor or variable lighting system for example. • Before connecting the piano to other devices, turn off the power to all units; this will help prevent damage or malfunction. [Exterior Care] • Use a feather-duster or soft rag to remove dust. • When you wish to polish the instrument, use only a piano-grade polish (but never use the polish on the keyboard itself). Never use solvents or abrasive chemical cleaners. [Keyboard Care] • Clean with a soft, damp cloth, then wipe thoroughly with a dry cloth. • Do not, under any circumstances, use benzene, thinners or alcohol-based cleaners, which can discolor or deform the plastic keys. • Of course, it helps to not play the keyboard when your hands are dirty, and... • ...you should keep the dust cover (keyboard lid) closed when the instrument is not being played. [Precautions] • The keyboard cover on the HP-5700 is a sliding type. Use both hands to smoothly guide it into place. Don't try to force it or slam it shut. • Watch your fingers when opening or closing the cover. This especially applies to the HP-7700, with it's extra-large cover. Smaller children might need some help. • Be sure the music stand does not tilt too far forward, as this might damage it. \) I • Much of the exterior of the piano is made of wood, so avoid exposing it to abrupt changes in temperature and humidity. • Do not sit on top of the piano. • Do not set any of the...