Assessments - 3, GPA: 2.7
(
)
)
|
Facilidade de uso
fig.mic-guitar Connections The sound from the mic connected to INPUT 1 will be recorded into your computer on the left (L) channel. If you connect it to INPUT 2, the sound will be recorded on the right (R) channel. If you’re using a guitar, connect it to INPUT 2. Don’t connect anything to input jacks you’re not using. Howling could be produced depending on the location of microphones relative to speakers. This can be remedied by: 1. Changing the orientation of the microphone(s). 2. Relocating microphone(s) at a greater distance from speakers. 3. Lowering volume levels. Input sensitivity knob Use the input sensitivity knob to adjust the input level. In order to record at the best possible audio quality, adjust the input sensitivity knob until it is as high as you can get it without causing the input/output level indicator to light in red. Recording a mic or guitar Guitar/bass Mic Adjust the input level Adjust the input level Connect to INPUT 2 Turn this toward the right of center if you want the sound from the input jacks to be louder than the playback from the computer. Hi-z Monitor in stereo Monitor in monaural Set the sample rate Turn ON if you’re using a condenser mic Turn this on if there is a possibility that sudden high-volume sound may be input Make sure that the red LED does not light Basic connections and settings Basic connections and settings If a mic is connected to INPUT 2 Off If a guitar is connected to INPUT 2 On Limiter switch If you turn on the limiter switch, the input level will automatically be adjusted if a sudden loud sound is applied to the combo input jack. This makes it less likely that clipping noise will occur. Sample rate select switch Set this to the same sample rate that you’ve selected in your recording software. After you’ve changed the sample rate setting of the UA-101, you must cycle the power to the UA-101 in order for the setting to take effect. STEREO/MONO select switch (Direct Monitor section) Use this to select to monitor the input signal in stereo or in monaural. Direct Monitor Soft Control switch Turn this on if you want to control input monitoring from ASIO 2.0 compliant software or from UA-101 Control Panel (p. 38). Direct monitor volume This adjusts the balance between the monitor volume and the volume of the audio playback from the computer. Using the Direct Monitor volume control to adjust the volume will not affect the recording level. Phantom power switch If you’re using condenser mics, turn on the phantom power switch. * If you’ve connected a device that does not require phantom power, you must turn the phantom power switch off to avoid damaging your device. Basic connections and settings Recording a digital signal Basic connections and settings Recording a digital signal Set the sample rate Set this to the sample rate of your digital playback device ON CD/MD/DAT player, hard disk recorder, etc. Connections Connect your digital audio device to the digital input connector. Sample rate select switch Set this to match the sample rate you’ve selected on your digital audio playback device and in your recording software. After you’ve changed the sample rate setting of the UA-101, you must cycle the power to the UA-101 in order for the setting to take effect. You can’t record digital signal if you’ve selected 192 kHz. Digital input switch Turn this on so that the UA-101 will synchronize to the digital signal being input to the digital input connector. If the UA-101 is synchronized to the incoming signal, the SYNC indicator will light green. If the indicator is blinking green, synchronization has not been achieved. Please make sure that the sample rate of the connected digital device matches the setting of the UA-101’s sample rate select switch. Direct monitor volume This adjusts the monitor volume. Using the Direct Monitor volume control to adjust the volume will not affect the recording level. 31 Basic connections and settings fig.various Connections Connect output jacks 1–8 to your external mixer, etc. Connect the outputs of your external mixer, synthesizer, etc. to input jacks 3–8. Direct monitor volume This adjusts the monitor volume. Using the Direct Monitor volume control to adjust the volume will not affect the recording level. Connecting various equipment Mixer, DJ mixer, etc. Amplified speakers USB cable Guitar/bass Mic Computer Synthesizer, etc. Effects processor, mixer, etc. Basic connections and settings 5.1 channel monitoring Basic connections and settings 5.1 channel monitoring 5.1 ch speaker system Connections Connect phone-type audio cables to the output jacks. Patching within the UA-101 Use UA-101 Control Panel to patch the connections as follows. For details on UA-101 Control Panel, refer to “UA-101 Control Panel” (p. 38). In the PATCH BAY area of UA-101 Control Panel, set OUTPUT 1-2 to WAVE OUT 1-2, OUTPUT 3-4 to WAVE OUT 3-4, and OUTPUT 5-6 to WAVE OUT 5-6. Settings in Windows 1. From Windows Control Panel, open Sounds and Audio Devices Propertie...