Assessments - 3, GPA: 4
(
)
)
|
Facilidade de uso
* Howling could be produced depending on the location of microphones relative to speakers. This can be remedied by: 1. Changing the orientation of the microphone(s). 2. Relocating microphone(s) at a greater distance from speakers. 3. Lowering volume levels. REMOTE Jack This jack is for connecting a foot switch (BOSS FS-5L; optional). A foot switch allows you to turn the voice character function on/off without affecting the reverb component. AC Adaptor Jack Connect the included AC adaptor (ACI/ACB Series) to this jack. Number Buttons / Number Indicators These buttons are used to select memory positions 1 – 4; the indicator of the selected number will light. When you move the sliders or press the ROBOT button, the number indicator will blink to indicate that the voice character is now different than the contents of the memory. ROBOT Button / Robot Indicator This button turns the Robot function on/off. When the Robot function is on, the Robot indicator will light. When the Robot function is on, the voice will be output at a fixed pitch (regardless of the input pitch), producing a flat voice character without intonation. WRITE Button This button is used to write (store) the current voice character settings into memory (the USER bank). Write procedure Here’s how to write a voice character that you’ve created into memory (USER bank). By storing a voice character in memory, you can later re-select it at the touch of a button. 1. Move the sliders and/or press the ROBOT button to create the desired voice character. 2. Press the WRITE button. The bank (USER) and number indicators will blink. 3. Press a number button (1 – 4) to select the desired storage destination; the number indicator will blink. 4. Press the WRITE button once again. The voice character will be stored in the number you selected in step 3. * By pressing the WRITE button without moving the sliders or pressing the ROBOT button, you can copy the currently selected voice character to another USER number. * If during the Write procedure you decide to cancel the operation, hold down the BYPASS button and press the WRITE button. You will return to where you were before starting the Write procedure. FORMANT Slider Formants are fixed frequency regions of emphasis that are an important element in determining how a voice sounds. This slider adjusts the formants. Raising the slider produces a voice character that sounds as if the vocal cords have become ‘smaller.’ Lowering the slider produces a voice character that sounds as if the vocal cords have become ‘larger.’ PITCH Slider This slider adjusts the pitch of the voice character. The pitch can be adjusted over a range of +/- one octave. MIX BALANCE Slider This slider adjusts the volume balance between the generated voice character and the original input sound. As the slider is raised (toward the EFFECT end of the scale), the generated voice character will become louder. Bank Buttons / Bank Indicators These buttons are used to select memory banks; they switch between the Preset bank and the User bank. Preset bank: This bank contains preset voice characters. It is not possible to re-write the contents of these memories. User bank: Voice characters that you create using the sliders and the ROBOT button can be stored in these memories. PEAK Indicator This indicator lets you check the microphone input level. If the indicator lights frequently, lower the input level by adjusting the INPUT LEVEL knob located on the rear panel. * The PEAK indicator will light 6 dB below the clipping point (the level at which distortion will begin). * If the PEAK indicator lights too frequently, the proper effect will not be obtained. BYPASS Button / Bypass Indicator This button switches the bypass function on/off. When bypass is on, the BYPASS indicator will light, and the voice character and reverb will be turned off so that the input sound is output without change. If you use the REMOTE jack to turn off the voice character (while leaving the reverb unaffected), the Bypass indicator will blink. REVERB Slider This slider adjusts the volume of the reverberation sound. Selecting Preset Memories You can choose from five voice character types as appropriate for your musical or performance situation. The voice character memories will be given settings of the selected type. At this time, the contents of the USER bank will also be re-written. If All Memory Type is selected, you will be able to freely modify the settings of the PRESET bank just as with the USER bank. (Procedure) 1. Turn the power off. 2. While holding down the button for the desired type, turn the power on again. 3. While the Preset indicator and the User indicator are lit, press the WRITE button. The voice character memories will be given settings of the selected type: { [BANK]: Standard Settings } { [1]: Vocal Applications with reverb } { [2]: Vocal Applications with non-reverb } { [3]: Narrations / DJ Performance Settings } { [4]: Animation Character Settings } { [ROBOT]: ...