Assessments - , GPA:
(
)
)
Fabricante : Roland
Arquivo Tamanho: 58.73 mb
Arquivo Nome :
Língua de Ensino: 
O documento está colocado, por favor, espere
 |
O documento está colocado, por favor, espere
por este dispositivo também tem outras instruções :
Facilidade de uso
When the Edit Lock setting is turned on, a “ ” symbol will appear in the screen that appears immediately after you press the [POWER] button. The “ ” symbol will also appear in the Options screen where you select Factory Reset, and subsequent Factory Reset operations will not be possible. English Deutsch Francais Italiano Espanol Portugues Nederlands 43 g This section outlines points to check if you experience problems, and what to do about them. Demo patterns won’t play . Could you be recording? > If you press the [ ] (Rec) button to record your performance (p. 16), the demo patterns will temporarily be erased, but you will again be able to hear the demo patterns after you turn the power off, then on again. Recorded data has disappeared . Could you have turned off the power? > When you turn off the power after recording, the recorded data will be erased; the next time you turn on the power, the demo patterns will be recalled from internal memory. No Sound from One or More Pads . Is the volume level of an instrument lowered? > In the drum kit settings, adjust the mixer Pad Volume (p. 28). . Is the pad connected correctly? > Make sure that pad/input connections are correct. Use only the provided cables to connect the pads. . Is the instrument set to OFF? > OFF is the setting for producing no sound. Select an instrumentnumbered other than “OFF” (p. 47). . Could the pad type be “OFF”? > Make the correct Pad Type setting (p. 34). Pad Not Playing Correctly . Is the pad type setting correct? > Set the Pad Type (p. 34). . Is the pad’s sensitivity setting correct? > Set the Sensitivity (p. 34). * For fullest expression in performance, we recommend the exclusive use of Roland pads. . Is the pad’s mesh head tensioned evenly? > Refer to the owner’s manual for the pad you are using, then adjust the mesh head tension. This is very important for proper triggering. . When you strike a pad, you hear a pad you didn’t strike > Adjust the Xtalk Cancel setting (p. 42). > If there is a pad you’re not using, turn that pad’s Pad Type “OFF” (p. 34). Cannot Play Rim Shots/Edge Shots . Are you playing the rim shot correctly? > For a rim shot, use the stick’s shoulder to strike the rim of the pad. . Is the Rim Adjust set to “0” ? > Set this to anything other than “0” (p. 42). You need to set the “Rim Adjust” when using the PD-85, PD105, or PD-125 to play rim shots. Cross Stick Does Not Work . Are you playing the cross stick correctly? > Playing cross stick on electronic drums is a bit different. Be sure your hand or stick does not strike the head also. . Is the Xstick Volume set to “OFF”? > Set the Xstick Volume to a value other than “OFF” (p. 28). Troubleshooting Troubleshooting . Is the metronome volume level set to “0” ? > Set the metronome Volume to a value other than “0” (p. 33). No Ambience Applied . Is the Ambience set to “OFF” ? > Set the Ambience to a value other than “OFF” (p. 29). . Is the Ambience Depth set to “0” ? > Set the Ambience Depth to a value other than “0” (p. 29). Sound in Headphones Distorted . Sometimes, setting the output too high certain tones can the sound seem distorted. > Turn down the [VOLUME] knob. This will reduce the distortion. Output Sound is Distorted . Depending on the instrument settings, some slight distortion may occur in the sound. > In the drum kit settings, adjust the mixer Pad Volume (p. 28). > You can suppress distortion by setting the pan near the center. In the drum kit settings, adjust the mixer pan setting (p. 28). No Sound/Low Volume from Source Connected to the MIX IN Jack . Could you be using a connection cable that contains a resistor? > Use a connection cable that does not contain a resistor. . Check the volume level of the connected audio source. > See the owner’s manual for the device if there’s a problem. To adjust the volume of the device connected to the MIX IN jack, use the controls of the connected device. Can’t play the sound module connected to the MIDI OUT connector . Is the MIDI cable connected correctly? > Connect the cable to the MIDI IN connector of the external MIDI sound module. . Is the MIDI channel set correctly? > In order to transmit MIDI messages to an external MIDI sound module, both devices need to be set to the same MIDI channel (p. 39). . Have you specified the correct note number for the pad? > Set the pad’s note number to a value other than “OFF” (p. 39). > Make sure that the pad is set to the same note number as the sound on your external MIDI sound module. The note numbers can be specified independently for each kit. Others . Settings are not saved > There is no “Save Settings” operation on the TD-4 itself. The settings you modify are saved when you turn off the power. Be sure to turn off the power by pressing the [POWER] button. . Screen display is difficult to read > After you’ve turned on the power, press the [MENU] button > SEL ] button > [OK] button in that order, and use the [-/+] dial to adjust the contrast (p. 36). English Deutsch Francais Ital...