Assessments - 3, GPA: 3.3
(
)
)
|
por este dispositivo também tem outras instruções :
Facilidade de uso
This system may receive a strong electrical shock, such as from a lightening bolt or excessive static electricity, or drop in power supply. Set this system to standby mode, and then disconnect the power cable. Wait for about 30 seconds, connect the power cable, and then turn on this system. 14 A digital or high- frequency equipment produces noises. The system may be placed close to digital equipment or high-frequency equipment. Place this system farther away from such equipment. — 24 En Additional information Additional information Cause Solution See page The system settings change automatically. When “HDMI CONTROL” is set to “ON”, operations of the TV (for example, changing channels, etc.) may change the system settings, such as the surround mode. Set “HDMI CONTROL” to “OFF” or set the system again by using its remote control. 23 The remote control does not operate the system. The system may be outside the remote control operation range. For information on the remote control operation range, refer to “Using the remote control”. 14 The remote control sensor of this system may be exposed to direct sunlight or lighting. Change the lighting. — The batteries may be worn out. Replace the batteries. 6 ¦ HDMI Problem Cause Solution See page “AUTO” set in the setup menu “AUDIO DELAY” does not operate. The TV does not support automatically adjusting the audio delay. Adjust the delay time manually (0 to 240 ms). 21 The HDMI control function does not operate properly. The number of the connected HDMI components is over the limit. Disconnect some of the HDMI components. — No picture or sound The connected HDMI component does not support high-bandwidth digital copyright protection (HDCP). Connect the HDMI component that supports HDCP. — ¦ Tuner Problem Cause Solution See page FM stereo reception is noisy. The characteristics of FM stereo broadcasts may cause this problem when the transmitter is too far away, or if the antenna quality is poor. Check the antenna connections. Try using a high-quality directional FM antenna. Set the reception mode to “MONO”. 12 — 17 There is distortion, and clear reception cannot be obtained, even with a good FM antenna. There is multi-path interference. Adjust the antenna position to eliminate multi-path interference. — The desired station cannot be tuned into with the automatic tuning method. The signal is too weak. Use a high-quality directional FM antenna. Set the reception mode to “MONO” and press TUNING / to change frequency by 1 step. — 16, 17 ADDITIONAL INFORMATION 25 En Additional information ¦ iPod Status message Cause Solution See page Unknown iPod The iPod being used is not supported by this system. Only iPod (Click and Wheel including iPod classic), iPod nano, iPod mini, and iPod touch are supported. — iPod connected Your iPod is properly stationed in the Yamaha iPod universal dock (such as YDS-11, sold separately) connected to the DOCK terminal of this system, and the connection between your iPod and this system is completed. Disconnected Your iPod was removed from the Yamaha iPod universal dock (such as YDS-11, sold separately) connected to the DOCK terminal of this system. Station your iPod back in the Yamaha iPod universal dock (YDS-11, sold separately) connected to the DOCK terminal of this system. 18 Charging Your iPod is charging. ¦ Bluetooth See Status message Cause Solution page Searching... The Yamaha Bluetooth wireless audio receiver (such as YBA-10, sold separately) and the Bluetooth component are in the process of the pairing. The Yamaha Bluetooth wireless audio receiver (such as YBA-10, sold separately) and the Bluetooth component are in the process of establishing the connection. Completed The pairing is completed. Canceled The pairing is canceled. Not found The system cannot find the Bluetooth component while performing the pairing or trying to connect to the Bluetooth component. BT connected The connection between the Yamaha Bluetooth wireless audio receiver (such as YBA-10, sold separately) and the Bluetooth component is established. Disconnected The Bluetooth component is disconnected from the Yamaha Bluetooth wireless audio receiver (such as YBA-10, sold separately). Not Available The pairing is performed when the Perform the pairing when the Yamaha Yamaha Bluetooth wireless audio Bluetooth wireless audio receiver (such as receiver (such as YBA-10, sold YBA-10, sold separately) is not connected 19 separately) is connected to the to the Bluetooth component. Bluetooth component. 26 En 27 En Additional information ADDITIONAL INFORMATION ¦ AIR SURROUND XTREME This system employs new technologies and algorithms that make it possible to achieve 7-channel surround sound with only front speakers, and without using wall reflections. Ordinarily, two front speakers, a center speaker, two surround speakers, and a subwoofer are necessary for enjoying 5.1 channel surround sound. Virtual 7.1 channel The AIR SURROUND XTREME technology, using only front speakers and subwoofe...
Este manual também é adequado para os modelos :Instrumentos musicais - YHT-S400 (1.66 mb)