Assessments - 4, GPA: 3.5
(
)
)
|
Facilidade de uso
ACCESSORIES Check that the following items are included. Speaker cable (10m) x 1 Mounting bracket x 1 Screw x 2 Pad x 2 PLACING THE SPEAKER Place the speaker precisely between the rear speakers as 2 Fasten screws into a firm wall or wall support as shown shown in the figure below. in the figure, and hang the holes of the mounting bracket on the protruding screws. Main R Rear R Rear L Subwoofer Center Main L NS-10MMTS ¦ To mount the speaker on a wall by using the provided mounting bracket 1 Attach the bracket to the rear of the speaker by using the provided screws. Remove the provided pads from the backing sheet and put them at the lower corners of the speaker. Pad Screw Mounting bracket * Make sure that the screws are securely caught by the narrow parts of the holes. Tapping screw (3.5–4 mm) (Available at the hardware store) 60 mm You can also use the screw holes on the bottom of the speaker for installing the speaker on commericially available speaker stand (if you do not use the provided mounting bracket.) A screw with a diameter of 4 mm can be used. (Hole depth : 10 mm) Wall/ wall support 40 mm Min. 20 mm 3 mm WARNING . This speaker weighs 1.5 kg (3 lbs. 5 oz.). Do not mount it on thin plywood or a wall with soft surface material. If mounted, the screws may come out of the flimsy surface and the speaker may fall.This damages the speaker or causes personal injury. . Do not install the speaker to a wall with nails, adhesives, or any other unstable hardware. Long- term use and vibrations may cause it to fall. . To avoid accidents resulting from tripping over loose speaker cable, fix it to the wall. . This speaker features a magnetically shielded design, but there is still a chance that placing it too close to a TV set might impair picture color. Should this happen, move the speaker away from the TV set. CONNECTIONS TO YOUR AMPLIFIER Before making connections, make sure that the amplifier is switched off. English – REAR CENTER + Amplifier or Receiver Tighten NS-10MMTS Loosen Black (–) Red (+) – + CONNECTIONS • Connect the screw-type input terminals at the rear of the speaker to the speaker output terminals of the amplifier (or receiver) with the speaker cable. • Connect the (+) terminals on the amplifier (or receiver) and the speaker using one side of the cable. Connect the (–) terminals on both components using the other side of the cable. • Connect the speaker to the rear center terminals of your amplifier (or receiver), making sure not to reverse the polarity (+, –). If the speaker is connected with reversed polarity, the sound will be unnatural and lack bass. How to connect: 1 Loosen the knob. 2 Remove the insulation coating at the extremity of each speaker cable by twisting the coating off. 3 Insert the bare wire. 4 Tighten the knob and secure the cable. Test the firmness of the connection by pulling lightly on the cable at the terminal. Note Do not let the bare speaker wires touch each other as this could damage the speaker or the amplifier, or both of them. When using a banana plug Banana plug 213 1 Remove the cover by pulling it toward you. 2 Tighten the terminal knob. 3 Simply insert the banana plug into the terminal. REMOVING THE FRONT COVER The front cover is fastened to the enclosure at four points and can be removed if desired. To remove the cover, hold on to both sides and slowly pull straight away from the speaker. To reattach, line up the four holes on the inner surface of the cover with the four corresponding pegs on the speaker and push gently. Note When the cover is removed, take care not to touch the speaker units with your hands or to exert excessive force with tools. SPECIFICATIONS Type ............................. 2-way bass reflex speaker system Magnetic shielding type Driver ........................................ 9 cm (3-1/2”) cone woofer 2.5 cm (1”) balanced dome tweeter Impedance ................................................................... 6 . Frequency Response ................................75 Hz to 33 kHz Nominal Input Power .................................................. 40 W Maximum Input Power.............................................. 100 W Sensitivity ...................................................88 dB/2.83 V/m Crossover Frequency ................................................. 7kHz Dimensions (WxHxD).........................107 x 191 x 141 mm (4-3/16” x 7-1/2” x 5-9/16”) Weight .................................................. 1.5 kg (3 lbs. 5 oz.) Accessories ................................. Speaker cable (10m) x 1 Mounting bracket x 1 Screw x 2 Pad x 2 . Specifications are subject to change without notice due to product improvements. . Care should be taken not to exceed the input power values noted above. YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A. YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR, 22-34, 25462 RELLINGEN, B...