Assessments - 5, GPA: 5
(
)
)
|
Fotos e especificações Yamaha A-S700 |
Facilidade de uso
Audio out Audio out GND Audio out Audio out Audio out Audio in Turntable Tape deck, etc. CD recorder, Speakers B etc. y • The PHONO jacks are designed to connect a turntable with an MM cartridge. • Connect your turntable to the GND terminal to reduce noise in the signal. However, you may hear less noise without the connection to the GND terminal for some turntable(s). 6 En CAUTION CAUTION CONNECTIONS • The IMPEDANCE SELECTOR must be set to the appropriate position before connecting one or two speaker sets. See page 5 for details. • Do not let the bare speaker wires touch each other or do not let them touch any metal part of this unit. This could damage this unit and/or the speakers. • Do not connect this unit or other components to the main power until all connections between components are complete. 1 Remove approximately 10 mm (3/8 in) of insulation from the end of each speaker cable and twist the exposed wires of the cable together to prevent short circuits. 10 mm (3/8 in) 2 Connect the speaker cable. 1 Unscrew the knob. 2 Insert one bare wire into the hole in the side of each terminal. 3 Tighten the knob to secure the wire. Red: positive (+) Black: negative (–) ¦ Connecting via banana plug (Except for Asia, Korea, U.K. and Europe models) First, tighten the knob and then insert the banana plug into the end of the corresponding terminal. Banana plug ¦ Bi-wire connection The bi-wire connection separates the woofer from the combined midrange and tweeter section. A bi-wire compatible speaker has four binding post terminals. These two sets of terminals allow the speaker to be split into two independent sections. With these connections, the mid and high frequency drivers are connected to one set of terminals and the low frequency driver to another set of terminals. This unit Speaker Connect the other speaker to the other set of terminals in the same way. CAUTION When making bi-wire connections, set the IMPEDANCE SELECTOR switch to HIGH or LOW depending on the impedance of your speakers: 6 . or higher: HIGH 4 . or higher: LOW See page 5 for IMPEDANCE SELECTOR switch. Note When making bi-wire connections, remove the shorting bridges or cables on the speaker. y To use the bi-wire connections, switch the SPEAKERS selector to the A+B position. PREPARATION Note One or two speaker sets can be connected to this unit. 7 En English CONNECTIONS Connecting the supplied power cable (Asia and General models) To the wall outlet with the supplied power cable ¦ VOLTAGE SELECTOR (Asia and General models only) The VOLTAGE SELECTOR on the rear panel of this unit must be set for your local main voltage BEFORE plugging the supplied power cable into the wall outlet. Improper setting of the VOLTAGE SELECTOR may cause damage to this unit and create a potential fire hazard. Rotate the VOLTAGE SELECTOR clockwise or counterclockwise to the correct position using a straight slot screwdriver. Voltages are as follows: Asia model..........................AC 220/230–240 V, 50/60 Hz General model ......AC 110/120/220/230–240 V, 50/60 Hz ¦ AC OUTLET(S) (SWITCHED) U.K. and Australia models ..................................... 1 outlet Korea model .............................................................. None Other models ........................................................ 2 outlets Use these outlets to connect the power cables from your other components to this unit. The power to the AC OUTLET(S) is controlled by POWER on the front panel of this unit (or on the remote control). The outlet(s) supply power to any connected component whenever the power of this unit is turned on. For information on the maximum power (total power consumption of components), see “SPECIFICATIONS” on page 15. Note Do not connect components with a built-in amplifier, such as a subwoofer, etc. ¦ Connecting the supplied power cable Plug the supplied power cable into the AC IN on the rear panel of this unit and then, plug the power cable into the wall outlet after all other connections are complete. 8 En PLAYING AND RECORDING PLAYING AND RECORDING Playing a source 1 Rotate VOLUME on the front panel to the extreme counterclockwise position. 2 Press POWER on the front panel inward to the ON position. 3 Rotate the INPUT selector on the front panel (or press one of the input selector buttons on the remote control) to select the input source you want to listen to. The indicator of the selected input source lights up. or Front panel Remote control Lights up 4 Rotate the SPEAKERS selector on the front panel to select SPEAKERS A, B or A+B. Notes • Switch the SPEAKERS selector to the A+B position when making bi-wire connections, or when using two sets of speakers simultaneously (A and B). • If you listen with headphones, rotate the selector to the OFF position. 5 Play the source. OPERATION English 9 En PLAYING AND RECORDING 6 Rotate VOLUME on the front panel (or press VOL +/– on the remote control) to adjust the sound output level. or Front panel Remote control y You can ...