Assessments - , GPA:
(
)
)
Fabricante : Yamaha
Arquivo Tamanho: 3.53 mb
Arquivo Nome :
Língua de Ensino: 
O documento está colocado, por favor, espere
 |
O documento está colocado, por favor, espere
Facilidade de uso
18 A percussive noise is heard when playing back a source encoded with DTS. If the input mode is set to AUTO, depending on some sources, there may be a noise heard while this unit is identifying the format of the input signal. Set the input mode of the currently selected input source to DTS. 18 No sound is heard when playing back a source encoded with DTS, even if the input mode is set to AUTO on this unit. The built-in DTS decoder does not function because the player has a digital volume control and it is set at a position other than “maximum,” “neutral” or “ineffective.” Set the player’s digital volume control at the maximum, neutral or ineffective position. — No sound is heard when playing back an MD or DAT on which has been recorded a source encoded with DTS. A source encoded with DTS cannot be recorded on an MD or DAT. — No sound is heard when playing back a source (CD, etc.) even if the currently selected input mode is AUTO. In the AUTO mode, the DTS-decoding mode cannot be automatically changed to the normal (PCM) digital signal input mode. Set the input mode to AUTO again. 19 Notes • It is necessary to use a DTS decoder to play back a source encoded with DTS, so the player which plays back the source must be connected to a digital audio input terminal of this unit in the way described in this manual. If this connection is not made or only a D-to-A converter is being used without using a DTS decoder, only a loud hissing noise will be heard when you play back the source. • The “t” indicator will flash when the input mode is set to AUTO and a search or skip operation is performed while playing back a source encoded with DTS. If this status continues for 30 or more seconds, the unit will automatically switch from DTS-decoding mode to PCM digital signal input mode and the “t” indicator will go out. SPECIFICATIONSE AUDIO SECTION • Minimum RMS Output Power 20 Hz to 20 kHz, 0.06% THD, 8 ohms Center, Rear L/R ......................................................................... 70 W 1 kHz, 0.09% THD, 8 ohms Center, Rear L/R ......................................................................... 80 W • Maximum Output Power (EIAJ) 1 kHz, 10% THD, 8 ohms ........................................................ 105 W • DIN Standard Output Power 1 kHz, 0.7% THD, 4 ohms Center, Rear L/R ....................................................................... 110 W • IEC Output Power 1 kHz, 0.04% THD, 8 ohms ....................................................... 75 W • Dynamic Power (IHF) 8/6/4/2 ohms ........................................................ 90/110/135/160 W • Damping Factor 20 Hz to 20 kHz, 8 ohms ................................................................ 80 • Frequency Response CD etc. to MAIN L/R .............................. 10 Hz to 100 kHz, 0/–3 dB • Total Harmonic Distortion (20 Hz to 20 kHz) 6CH INPUT to REAR SP OUT, 35W/8 ohms ....................... 0.06 % • Signal-to-Noise Ratio (IHF-A Network) CD etc. to MAIN PRE OUT (250 mV, Input Shorted) ........................................................ 103 dB • Residual Noise (IHF-A Network) CENTER, REAR SP OUT ..................................................... 150 mV • Input Sensitivity/Impedance CD etc. ................................................................. 150 mV/47 k-ohms 6CH INPUT ......................................................... 150 mV/47 k-ohms • Output Level/Impedance REC OUT ........................................................... 150 mV/1.2 k-ohms PRE OUT ................................................................ 1.0 V/1.2 k-ohms SUBWOOFER ........................................................ 4.0 V/1.2 k-ohms • Channel Separation (Vol. –30 dB) CD etc. (Input 5.1 k-ohms terminated, 1 kHz/10 kHz) ..................................................................................... 60 dB/45 dB VIDEO SECTION • Video Signal Type ........................................................... NTSC or PAL • Video Signal Level ....................................................... 1 Vp-p/75 ohms • Signal-to-Noise Ratio .................................................................. 50 dB • Monitor Out Frequency Response .................... 5 Hz to 10 MHz, –3 dB GENERAL • Power Supply ............................................................. AC 230 V, 50 Hz • Power Consumption .................................................................... 180 W • AC Outlet (100 W max. total) ..................................... 1 (SWITCHED) • Dimensions (W x H x D) ...................................... 435 x 126 x 391 mm • Weight ....................................................................................... 10.0 kg • Accessories ................................................................... Remote control ........................................................................................... Batteries Specifications are subject to change without notice. E-35 EnglishAPPENDIX ATTENTIO...