Assessments - 5, GPA: 3.8
(
)
)
|
por este dispositivo também tem outras instruções :
Facilidade de uso
CH Note No. 1 37 (25h) 3 38 (26h) 5 39 (27h) 7 40 (28h) 9 41 (29h) 11 42 (2Ah) 13 43 (2Bh) 15 44 (2Ch) Also, Note-on/off messages are received when the Effect is being frozen and MIDI TRG is not set to OFF. In this case, the velocity is ignored. 1.1.2 Control Changes Control change messages will be transmitted or received when transmission or reception are respectively turned on. With a setting of OMNI, all channels will be received. The 114 control numbers 0 through 95 and 102 through 119 can be freely assigned to mixer parameters. Note: 0 and 32 are Bank Change messages, and in the case of a device which cannot transmit or receive these correctly unless they are used in conjunction with a Program Change message, it is possible that there will be problems with operation. In this case, do not assign 0 or 32. Data values for transmission and reception are calculated as follows. Given the following: (128 or in the case of two-byte data 16384) / (number of parameter steps) = X...Y INT ((Y+1) / 2) = Z Reception If (MIDI DATA -Z) < 0, then INTERNAL = 0 If ((MIDI DATA -Z) / X) > MAX, then INTERNAL = MAX Else, INT ((MIDI DATA -Z) / X) = INTERNAL Transmission If INTERNAL = 0, then MIDI DATA = 0 If INTERNAL = MAX then MIDI DATA = (127 or in the case of two-byte data 16384) Else, (X x INTERNAL) + INT (X / 2) + Z = MIDI DATA 1.1.3 Program Changes Transmission/reception of these messages can be turned on/off in the MIDI page. When a memory recall is executed, the program change message corresponding to that memory number will be transmitted on the specified MIDI channel. If a program change message is received on the specified MIDI channel or in OMNI, the memory corresponding to that program number will be recalled. The user is free to create the program change assign table. 1.2 System Exclusive Messages 1.2.1 Bulk Dump/Request Transmission is always on. Reception can be specified. Bulk Request messages can be transmitted on the specified MIDI channel by operations in the MIDI page. Bulk Dumps can be transmitted by operations in the MIDI page, or in response to an incoming Bulk Request that is received on the specified DEVICE channel. The contents of the corresponding memory will be transmitted on the specified DEVICE channel. When a Bulk Dump is received, the contents of the corresponding memory will be rewritten. 1.2.2 Parameter Change/Request Transmission / reception can be turned on/off in the MIDI page. When a parameter of this unit is edited, a parameter change message will be transmitted on the specified DEVICE channel if Parameter Change Transmission is on. If Parameter Change Reception is on, receiving a Parameter Request on the specified DEVICE channel will cause the content of the corresponding parameter to be transmitted, regardless of whether transmission is on or off. When Parameter Change Reception is on, and a Parameter Change is received on the specified DEVICE channel, the contents of the corresponding parameter will be modified. 1.2.3 MMC (MIDI Machine Control) These messages can be transmitted according to the User Define settings. 1.3 System Common Messages 1.3.1 MTC Quarter Frame Messages Received by Automix for synchronization. 1.3.2 Song Position Pointer When Automix is set to MIDI Clock Base, these messages are received, and a following Continue command will cause synchronization to begin from the middle of the song. 1.4 System Real Time Messages 1.4.1 Timing Clock These are received for synchronization when Automix is set to MIDI Clock Base. 1.4.2 Start, Continue, Stop These are received when Automix is set to MIDI Clock Base, and will start/stop the automix. These can also be transmitted according to the User Define settings. 1.4.3 Active Sensing This is transmitted at intervals of less than 300 ms. If after this message is received, no message is received for an interval longer than 300 ms, Running Status will be cleared. 1.4.4 System Reset When this is received, Running Status will be cleared. 1.5 MIDI Remote MIDI Remote settings allow all MIDI commands to be transmitted on the specified channel. Control Change, Program Change, and Exclusive messages will be received in the format determined for the specified model. 1.6 Echo Back This setting allows each received command to be re-transmitted. 03D—Manual de Instrucciones MIDI Data Format 289 MIDI Data Format 289 Transmission Condition MIDI TRG ON MIDI OUT PGM ECHO ON CTL ECHO ON REAL TIME & MTC ECHO ON OTHER ECHO ON PARAM ECHO ON MIDI IN FD Tx CH? MIDI Tx CH? DEVICE CH? MMC CH? REMOTE CH? PARAM Tx ON CTL Rx ON PGM Rx ON NOTE ON/OFF $9nH CONTROL CHANGE $BnH BULK REQUEST $F0H, $43H, $2nH ACTIVE SENSE $FEH MIDI REMOTE PROGRAM CHANGE $CnH (RESPONSE FOR PARAMETER REQUEST) SYSTEM EXCLUSIVE PARAMETER CHANGE $F0H, $43H, $1nH SYSTEM EXCLUSIVE BULK DUMP $F0H, $43H, $0nH USER DEFINE MMC $F0H, $7FH, nnH, 06H START $FAH CONTINUE $FBH STOP $FCH 3. Receive Condition MIDI TRG ON $8nH NOTE OFF $9nH NOTE ON/OFF CTL Rx ON MIDI CLOCK BASE PGM Rx ON PARAM Rx ON ...