TRANSMIT/RECEIVE DATA 1.1 CHANNEL MESSAGE 1.1.1 CONTROL CHANGE (Bn) BANK SELECT In PROGRAM CHANGE SINGLE CH mode when [Bank] is ON, this message can be received via the MIDI IN for BANK SELECT reception is enabled, if the [Rx CH] matches. This will specify the bank for a subsequently-received program change. In SINGLE CH mode when [Bank] is ON and you recall a scene memory or effect library, a bank select message will be transmitted (before the program change message) from the selected MIDI OUT, on the specified [Tx CH]. STATUS 1011nnnn Bn Control Change 00000000 00 Bank Select MSB 0vvvvvvv vv MSB Value 00100000 20 Bank Select LSB 0vvvvvvv vv LSB Value 1.1.2 CONTROL CHANGE (Bn) ASSIGN If CONTROL CHANGE ASSIGN is ON and CONTROL CHANGE is set to SINGLE CH mode, this message can be received from the MIDI IN for which reception is enabled, if the [Rx CH] matches. The parameter that is assigned in the [Control Change Table] will be modified. In MULTI mode, any MIDI channel will be received. The received MIDI channel (i.e., its number) will be added to the number of the parameter assigned in the [Control Change Table] (the same number as NRPN) to determine the parameter that will be modified by the message. This message is not echoed, but will be transmitted as described below even when a parameter is modified as a result of the MIDI reception. In SINGLE CH mode, when a parameter assigned in the [Control Change Table] has been modified, this message will be transmitted from the MIDI OUT for the selected [Tx CH]. In MULTI CH mode, when a parameter corresponding to a parameter number (same as NRPN) assigned in the [Control Change Table] +15 or less is modified, this message will be transmitted from the selected MIDI OUT, with the MIDI channel representing the difference from the parameter number. If the parameter is assigned to more than one control number, the message will be transmitted using the lowest- numbered control number. If a parameter with a resolution of greater than 7 bits is assigned to a control number in the range of 1–31, that control number +32 can be assigned as the LSB of the same parameter. STATUS 1011nnnn Bn Control Change 0ccccccc cc Control No.(1-5,7-31,3337,39- 95,102-119) 0vvvvvvv vv Value The transmitted and received values are calculated as follows. (The same applies to the NRPN messages discussed later.) Given the following: (128 or 16384 in the case of word data) / (number of parameter steps) = X ...Y INT (( Y + 1) / 2 ) = Z Reception: If ( MIDI data -Z ) < 0, then parameter = 0 If (( MIDI data - Z ) / Z ) > MAX, then parameter = MAX Otherwise, INT ( MIDI data - Z ) / X ) = parameter Transmission: If parameter = 0, then MIDI data = 0 If parameter = MAX, then MIDI data = (127 or 16383 in the case of word data) Otherwise, ( X x parameter ) + INT ( X / 2 ) + Z = MIDI data 1.1.3 CONTROL CHANGE (Bn) NRPN If NRPN is ON and if the [Rx CH] matches, this message can be received at the MIDI IN for which reception is enabled. There is a one-to-one correspondence between the received NRPN number and the parameter that will change. (See the “MIDI control change NRPN (Non Registered Parameter Number) assignment table”.) This message is not echoed, but the transmission described below will occur even if a parameter is modified due to MIDI reception. If NRPN is ON and a parameter is modified, this message will be transmitted from the MIDI OUT selected by [Tx CH]. If both CONTROL ASSIGN and NRPN are simultaneously ON, an assigned parameter will be transmitted as a control change. If the parameter has a resolution of less than 7 bits, only the MSB data will be transmitted. STATUS 1011nnnn Bn Control Change 01100010 62 NRPN LSB 0vvvvvvv vv MSB Value 01100011 63 NRPN MSB 0vvvvvvv vv LSB Value 00000110 06 DATA ENTRY MSB 0vvvvvvv vv MSB Value 00110110 26 DATA ENTRY LSB 0vvvvvvv vv LSB Value 60 h (INC) and 61 h (DEC) are not supported. 1.1.4 PROGRAM CHANGE (Cn) If [Program Change Rx] is ON, this message can be received at the MIDI IN for which reception is enabled, if the [Rx CH] matches in the case of SINGLE mode. However if [OMNI] is ON, this message will be received regardless of the channel. In the case of MULTI mode, all MIDI channels will be received and will be divided into banks according to the channel. If [Program Change ECHO] is ON, this message will be echoed. A scene memory or effect library will be recalled according to the settings of the [Program Change Table]. If [Program Change TX] is ON, this message will be transmitted from the selected MIDI OUT on the [Tx CH] channel (in the case of SINGLE mode), when a scene or effect library is recalled. In the case of MULTI mode, this will be transmitted on the MIDI channel according to the bank. If the recalled memory number is assigned to more than one program number, the program number for the lowest-numbered channel of the lowest-numbered ba...
)
