Assessments - 4, GPA: 4.5
(
)
)
|
Facilidade de uso
Use | | master AM602 MASTER fader. | 6 INPUT CHANNELS ST OUT f SUB IN/OUT switchl 6 INPUT CHANNELS ( A SUB IN/OUT switch set to IN set to OUT OUT IN OUT IN Bin HUM * V-. .............. ....................... -f - IMPORTANT NOTES - * MAKE SURE THE MIXER’S POWER SWITCH IS OFF OR THE MASTER FADER IS SET TO MINIMUM WHEN CONNECTING OR DISCONNECTING ANY CABLES. * ALWAYS TURN THE MIXER’S POWER ON OR RAISE THE MASTER FADER AFTER TURNING ON CONNECTED SOURCES SUCH AS ELECTRONIC INSTRUMENTS, ETC. * NEVER CONNECT THE SPEAKER OUTPUT OF ANY AMPLIFIER TO THE MIXER’S INPUTS UNLESS A SUITABLE HIGH-LEVEL ATTENUATION PAD OR “DIRECT BOX” IS USED TO LOWER THE SIGNAL’S LEVEL. -5- SAMPLE APPLICATION A Small Sound Reinforcement System In this small sound reinforcement system the required sources are connected to the appropriate input channel connectors. The AUX SND 1 output is connected to a digital signal processor for reverb and other effects, and the stereo output from the signal processor is returned to the AUX RTN 1 connectors. The AUX 1 controls can thus be used to set up the required effect mix..The AUX 2 controls are used to provide a separate monitor mix for the performers on stage. The AUX SND 2 output is therefore connected to a power amplifier driving the on-stage monitor speaker system. The main house power amplifier/speaker system can be fed by the ST OUT L and R outputs. In this system a tape player is connected to the AUX RTN 2 inputs to provide background music during intermission or recorded accompaniment for the performance. 6- BLOCK DIAGRAM -J CH o z o u DIMENSIONS 37 (1-7/16") UNIT = mm (inch) -7- SPECIFICATIONS Frequency Response +1, -2 dB, 20 Hz — 20 kHz, 10 kohms, 0 dB (ST OUT) +1, -2 dB, 20 Hz — 20 kHz, 10 kohms, -10 dB (AUX SND 1, 2), (SUB OUT) Total Harmonic Distortion Less than 0.05%, 20 Hz — 20 kHz, 10 kohms, +10 dB Hum & Noise* (20 Hz — 20 kHz, Rs = 150 ohms, CH1, 2 Gain max.) -122dB(CH1, 2) equivalent input noise. -90 dB (ST OUT) residual output noise. -76 dB (76 dB S/N) at ST OUT, Master fader nominal, all channel faders minimum. -72 dB (72 dB S/N) at ST OUT, Master fader nominal, channel 1, 2 faders nominal. -88 dB (78 dB S/N) at AUX SND, all channel AUX controls minimum. -82 dB (72 dB S/N) at channel 1, 2 faders nominal, AUX controls nominal. Maximum Output Level +17.5 dB, 20 Hz — 20 kHz, 10 kohms, THD 0.2% Maximum Voltage Gain 62 dB CH1, 2 IN to STOUT 22 dB CH3 — 6 IN to ST OUT 58 dB CH1, 2 IN to AUX SND 18 dB CH3 — 6 IN to AUX SND 32 dB AUX RTN to ST OUT 16 dB SUB IN (ST) to ST OUT 6 dB SUB IN (AUX) to AUX SND Crosstalk -60 dB at 1 kHz, adjacent channel inputs. -60 dB at 1 kHz, input to output. Input Channel Equalization (CH1, 2) 15 dB maximum boost or cut HI: 10 kHz (shelving) LO: 100 Hz (shelving) Clip Indicators (ST L, R) CLIP (red) lights when ST OUT signal is 3 dB below clipping. Signal Indicators (ST L, R) SIGNAL (green) lights when ST OUT signal reaches -10 dB (10 dB below nominal output level.) Power Requirement Power requirements match local AC mains voltage and frequency in area where sold. Power Consumption 9 watts Dimensions (W x H x D) 318 x 86 x 228 mm (12-1/2” x 3-3/8” x 9”) Weight 1.8 kg (3 lbs. 15 oz) * Measured with a -6 dB/octave LPF @ 12.7 kHz. • 0 dB = 0.775 Vrms -8- ■ INPUT CHARACTERISTICS Input terminals Input SW Gain Trim Actual Load Impedance For Use With Nominal Input Level Connector In Mixer Sensitivity* Nominal Maximum before clip CH 1, 2 MIC MAX 10 kohms 50-600 ohms Mies & 600 ohms Lines -62dB (0.62mV) -50dB (2.5mV) —28dB (31 mV) Phone jack MIN -37dB (11 mV) -25dB (44mV) -3dB (549mV) LINE MAX -43dB (5.5mV) -31 dB (22mV) -9dB (275mV) MIN -22dB (62mV) -1 OdB (245mV) +12dB (3.1V) CH 3 — 6 Input 10 kohms 600 ohms Lines -22dB (62mV) -1 OdB (245mV) ................................................................ Phone jack AUX RTN 1, 2 10 kohms 600 ohms Lines -32dB (19mV) -20dB (78mV) .................................................................. Phone jack SUB IN 10 kohms 600 ohms Lines -16dB (123mV) -1 OdB (245mV) ...................................................................... RCA Pin jack m OUTPUT CHARACTERISTICS Output terminals Actual Source Impedance For Use With Nominal Output Level Connector In Mixer Nominal Maximum before clip ST OUT 600 ohms 10 kohms Lines OdB (0.775V) +17.5dB (5.8V) Phone jack AUX SND 1, 2 600 ohms 10 kohms Lines -1 OdB (245mV) +17.5dB (5.8V) Phone jack PHONES 100 ohms 8 ohms Phones -22dB (62mV) -4.5dB (462mV) STEREO Phone jack SUB OUT 600 ohms 10 kohms Lines -1 OdB (245mV) +17.5dB (5.8V) RCA Pin jack • 0 dB = 0.775 V • All Phone Jack are unbalanced. • Sensitivity is the lowest level that will produce an output of 0 dB (0.775 V), or the nominal output level when the unit is set to maximum gain. -9- IMPORTANT NOTICE FOR THE UNITED KINGDOM Connecting the Plug and Cord IMPORTANT. The wires in this mains l...