Assessments - 5, GPA: 4
(
)
)
|
por este dispositivo também tem outras instruções :
Facilidade de uso
Matrix 1–2 signals are output in monaural via the MATRIX OUT 1–2 jacks (rear panel K). A M1–M4 level controls These control knobs enable you to adjust the input level of MIX bus 1–4 post-fader signals. B L/R controls 1 These control knobs enable you to adjust the input level of the ST bus post-fader signals for the L channel and R channel independently. C LEVEL control This control knob enables you to adjust the output level of Matrix 1–2 signals. 2 D ON switch This switch turns on and off Matrixes 1–2. When you turn this switch 3 off, the corresponding matrix signal is not output from the MATRIX 4 OUT jack. The signal is not sent to the AFL bus, either. E AFL (After-fader Listen) switch 5 When you turn this switch on, the matrix 1–2 post-fader signals are sent to the AFL bus. You can monitor the signals via the C-R MONITOR OUT jacks or PHONES jack. However, this switch will be disabled if the ON switch (4) is turned off. ST AFL LR LR 0 R 0 L 0 M4 0 M3 0 M2 0 M1 LEVEL AFLON 1 100 0 R 0 L 0 M4 0 M3 0 M2 0 M1 LEVEL AFLON 2 100 MATRIX 1 4 3 from MIX OUT MATRIX OUT 1,2LEVEL R L 2 AFL M4 M3 M2 M1 ON to Meter Signal flow in the MATRIX section GA32/12, GA24/12—Owner’s Manual 12 Master Section 12 Master Section C-R MONI PHONES ON PFL PFL/AFL TAPE IN LEVEL 100 LEVEL 100 C-R MONI (Control room monitor) section PHONES (headphones) section This section enables you to control signals monitored via the C-R MONITOR OUT jacks (see page 18, rear panel M) and the PHONES jack on the front panel (C-R MONI section/ PHONES section 6). A Monitor source select switch This switch enables you to select the type of signal to monitor via the C-R MONITOR OUT 1 jacks and the PHONES jack. 2 When the switch is set to PFL/AFL ( ) You will monitor PFL signals (signals routed from input channels/AUX returns to the PFL bus) 3 or AFL signals (signals routed from MIX buses 1–10/ST buses/MATRIX 1–2 to the AFL bus). 4 If any one of the PFL switches for the input channels/AUX returns is turned on, the PFL indicator 2 will light up. In this case, the PFL bus signals (not the AFL bus signals) are routed to the C-R MONITOR OUT jacks and PHONES jack. If all the PFL switches are turned off, the 5 AFL bus signals are sent to the C-R MONITOR OUT jacks and PHONES jack. Note: If you turn on any one of the PFL switches for the input channels/AUX returns while monitoring the AFL bus signal, the switching circuit will switch the signal to the PFL bus signal. When the switch is set to TAPE IN ( ) You can monitor the signals input from the TAPE IN jacks (see page 18, rear panel N). B PFL (Pre-fader Listen) indicator This indicator lights up when any one of the PFL switches for the input channels/AUX returns is turned on, indicating that the PFL bus signal is currently being monitored. C LEVEL control 6 This control enables you to adjust the level of signals output from the C-R MONITOR OUT jacks. This setting does not affect the signal level at the PHONES jack. D ON switch This switch turns on and off the monitoring signals output from the C-R MONITOR OUT jacks. It does not affect signals at the PHONES jack. E LEVEL (Headphones level) control This control enables you to adjust the level of signals output from the PHONES jack. This setting does not affect the signal level at the C-R MONITOR OUT jacks. F PHONES (Headphones) jack Tip (left) Connect monitoring stereo headphones here. See 1/4" TRS phone plug Ring (right) the figure on the right for wiring. Sleeve (ground) GA32/12, GA24/12—Owner’s Manual TAPE IN section 13 TAPE IN section 13 This section enables you to control line-level signals input from the TAPE IN jacks. Input signals from the TAPE IN jacks can be routed to the ST bus or directly to the C-R MONITOR OUT jacks and PHONES jack. TAPE IN ON 10 A ST (Stereo) control ST This control knob determines the level of input signals at the TAPE IN jacks that are sent to on 1 0 the ST buses. 2 B ON switch This switch turns on and off the signals sent from the TAPE IN jacks to the ST bus. This switch setting does not affect signals (input from the TAPE IN jacks) that are monitored via the C-R MONITOR OUT jacks and PHONES jack. Note: Set the Monitor source select switch (C-R MONI section 1) in the C-R MONI section to “TAPE IN” to monitor the TAPE IN signals via the C-R MONITOR OUT jacks and PHONES jack. 2 TAPE IN PFL R L TAPE IN PFL/AFL PFL LEVEL LEVEL MATRIX PFL•AFL/TAPE STON from AFL CTLRL 1 from MTRX ON RL ST L C-R MONITOR OUT R PHONES Signal flow in the C-R MONI section, PHONES section, and TAPE IN section GA32/12, GA24/12—Owner’s Manual 14 Master Section TALKBACK LEVEL ON INPUT ST M5-M10 M1-M4 100 651 432 Male XLR plug 1 (ground) 3 (cold) 14 Master Section TALKBACK LEVEL ON INPUT ST M5-M10 M1-M4 100 651 432 Male XLR plug 1 (ground) 3 (cold) 2 (hot) B M1-M4 switch C M5-M10 switch D ST switch These switches (2–4) are used to send talkback signals to MIX buses 1–4, MIX buses 5–10, and ST bus. You can turn the switches on or off independently for each destinatio...
Este manual também é adequado para os modelos :Instrumentos musicais - GA32/12 (477.9 kb)