Assessments - 2, GPA: 4
(
)
)
|
Facilidade de uso
before clipping Connector Specifications STEREO OUT (L, R) 75. 600. Lines +4dBu (1.23 V) +24 dBu (12.3 V) XLR-3-32 type (balanced [1 = GND, 2 = HOT, 3 = COLD]) TRS phone jack (balanced [Tip = HOT, Ring = COLD, Sleeve = GND]) GROUP OUT (1–4) 150. 10k. Lines +4dBu (1.23 V) +20 dBu (7.75 V) TRS phone jack (impedance balanced [Tip = HOT, Ring = COLD, Sleeve = GND]) AUX SEND (1–4) 150. 10k. Lines +4dBu (1.23 V) +20 dBu (7.75 V) TRS phone jack (impedance balanced [Tip = HOT, Ring = COLD, Sleeve = GND]) CH INSERT OUT (CHs 1–12) 75. 10k. Lines 0 dBu (0.775 V) +20 dBu (7.75 V) TRS phone jack (unbalanced [Tip = Out, Ring = In, Sleeve = GND]) REC OUT (L, R) 600. 10k. Lines -10 dBV (0.316 V) +10 dBV (3.16 V) RCA pin jack MONITOR OUT (L, R) 150. 10k. Lines +4 dBu (1.23 V) +20 dBu (7.75 V) TRS phone jack (impedance balanced [Tip = HOT, Ring = COLD, Sleeve = GND]) PHONES OUT 100. 40. Phones 3 mW 75 mW TRS phone jack Where 0 dBu = 0.775 Vrms and 0 dBV = 1 Vrms 76 MG206C/MG166CX/MG166C Owner’s Manual Specifications MG166CX/MG166C ¦ Electrical Specifications MIN TYP MAX UNIT Frequency Response STEREO OUT GROUP OUT EFFECT/AUX* SEND MONITOR OUT, REC OUT GAIN: min (CHs 1–11/12) 20 Hz–20 kHz Nominal output level @1 kHz Input: CHs 1 to 15/16, RETURN, 2TR IN -3.0 0.0 1.0 dB Total Harmonic Distortion (THD + N) STEREO OUT +14 dBu @ 20 Hz–20 kHz, Input GAIN Control at minimum 0.1 % Hum & Noise Hum & Noise are measured with a 6 dB/octave filter @ 12.7 kHz; equivalent to a 20 kHz filter with infinite dB/octave attenuation. CH INPUT 1–8 MIC STEREO OUT GROUP OUT EFFECT/AUX* SEND STEREO OUT GROUP OUT STEREO OUT EIN (Equivalent Input Noise): Rs = 150 ., GAIN: maximum -128 dBu STEREO OUT, GROUP 1-2 fader and GROUP 3-4 fader at nominal level and all channels’ ST and 1-2, 3-4 switches off. -88 Master EFFECT/AUX* control at nominal level and all CH EFFECT/AUX* controls at minimum. -81 STEREO OUT, GROUP 1-2, GROUP 3-4 faders and one CH fader at nominal level. -64 Residual Output Noise -98 Crosstalk (1 kHz) Adjacent Input Input to Output CHs 1–8 -70 dBSTEREO L/R, CHs 1–8, PAN: panned hard left or right -70 Maximum voltage gain (1 kHz) All faders and controls are maximum when measured. PAN/BAL: panned hard left or hard right Rs = 150 . INPUT GAIN: maximum Rs = 150 . Rs = 600 . MIC to CH INSERT OUT 60 dB MIC to STEREO OUT 84MIC to GROUP OUT MIC to GROUP to ST 94 MIC to REC OUT 62.2 MIC to MONITOR OUT, ST TO MONITOR 94 MIC to PHONES OUT 83 MIC to AUX SEND PRE 76 MIC to AUX SEND POST, EFFECT* SEND 86 CH 9/10, 11/12 LINE to STEREO OUT 58CH 9/10, 11/12 LINE to GROUP OUT CH 9/10, 11/12 LINE to AUX SEND PRE 47 CH 9/10, 11/12 LINE to AUX SEND POST, EFFECT* SEND 57 CH 13/14, 15/16 to STEREO OUT 34CH 13/14, 15/16 to GROUP OUT RETURN to STEREO OUT 16 RETURN to EFFECT/AUX* SEND 9 2TR IN to STEREO OUT 27.8 Phantom Voltage MIC no load 48 V ¦ General Specifications Input HPF CHs 1–11/12 80 Hz, 12 dB/oct Input equalization CHs 1–8 HIGH: 10 kHz (shelving) MID: 250 Hz–5 kHz (peaking) ±15 dB maximum LOW: 100 Hz (shelving) Turn over/roll-off frequency of CH 9/10–15/16 HIGH: 10 kHz (shelving) shelving: 3 dB blow maximum MID: 2.5 kHz (peaking) variable level. LOW: 100 Hz (shelving) PEAK Indicator Red LED turns on when post EQ signal (either post MIC HA or post EQ signal for CHs 9/10–15/16) reaches -3 dB below clipping (+17 dBu). Internal Digital Effect 16 PROGRAM, PARAMETER control (Only MG166CX) Foot Switch (Digital Effect On/Off) LED Level Meter Pre MONITOR Level 2x12 points LED meter (PEAK, +10, +6, +3, 0, -3, -6, -10, -15, -20, -25, -30 dB) STEREO/GROUP/PFL bus PEAK lights if the signal level reaches 3 dB below the clipping level. Power Supply Adaptor PA-30 AC 35 VCT, 1.4 A, Cable Length = 3.6 m Power Consumption 35 W (MG166CX), 30 W (MG166C) Dimensions (W x H x D) 478 mm x 102 mm x 496 mm Net Weight 5.5 kg (MG166CX), 5.3 kg (MG166C) All faders are nominal if not specified. Output impedance of signal generator: 150 ohms * MG166CX: AUX1, 2, EFFECT MG166C: AUX1, 2, 3 MG206C/MG166CX/MG166C Owner’s Manual 77 Specifications Specifications ¦ Input Specifications Input Connectors Gain Input Impedance Appropriate Impedance Sensitivity * Nominal Level Max. before Clipping Connector Specifications CH INPUT MIC (CHs 1–8) -60 dB 3k. 50–600. Mics -80 dBu (0.078 mV) -60 dBu (0.775 mV) -40 dBu (7.75 mV) XLR-3-31 type (balanced [1 = GND, 2 = HOT, 3 = COLD]) -16 dB -36 dBu (12.3 mV) -16 dBu (123 mV) +4 dBu (1.23 V) CH INPUT LINE (CHs 1–8) -34 dB 10k. 600. Lines -54 dBu (1.55 mV) -34 dBu (15.5 mV) -14 dBu (155 mV) TRS phone jack (balanced [Tip = HOT, Ring = COLD, Sleeve = GND]) +10 dB -10 dBu (245 mV) +10 dBu (2.45 V) +30 dBu (24.5 V) ST CH MIC INPUT (CHs 9/10, 11/12) -60 dB 3k. 50–600. Mics -80 dBu (0.078 mV) -60 dBu (0.775 mV) -40 dBu (7.75 mV) XLR-3-31 type (balanced [1 = GND, 2 = HOT, 3 = COLD]) -16 dB -36 dBu (12.3 mV) -16 dBu (123 mV) -6 dBu (389 mV) ST CH LINE INPUT (CHs 9/10, 11/12) -34 dB 10k. 600. Lines -54 dBu (1.55 mV) -34 dBu (15.5 mV) -14 dBu (155 mV) Phone jack (unba...
Este manual também é adequado para os modelos :Instrumentos musicais - MG166C (2.44 mb)
Instrumentos musicais - MG206C (2.44 mb)