Assessments - 1, GPA: 5
(
)
)
|
por este dispositivo também tem outras instruções :
Facilidade de uso
When the switch is pressed in the EQ is on. In addition to bypassing the EQ when it is not being used, this switch provides a convenient way to compare the equalized and unequalized signals. 7AUX 1 / AUX 2 controls These adjust the signal level that is sent to each output AUX SEND 1 and AUX SEND 2. These signals are pre-fader (i.e., they are taken from before the fader adjustment). Nominal level is at 3 o’clock position. 8AUX 3 / AUX 4 / AUX 5 controls These adjust the signal level that is sent to each output AUX SEND 3, AUX SEND 4 and AUX SEND 5. The signals controlled by AUX 3 and AUX 4 will depend on the setting of the PRE switch. • When the PRE switch is not pressed They control the post-fader signal. • When the PRE switch is pressed They control the pre-fader signal. AUX 5 controls the post-fader signal. Nominal level is at 3 o’clock position. MX400 User’s Guide Front and rear panels PAN L ODD R EVEN ON PFL ST 3–4 1–2 Front and rear panels PAN L ODD R EVEN ON PFL ST 3–4 1–2 10 5 0 5 10 15 20 25 30 40 . 9Assign switches (1-2, 3-4, ST) These switches assign the signal of the input module to the group outputs and the ST output. The PAN control located below adjusts the stereo posi 9 tion of the signal between the odd (ODD) group and left (L) outputs and the even (EVEN) group and right (R) outputs. 0PAN control 0 This knob adjusts the stereo position of the signal between the stereo L and R, and between the odd/even groups. For example if this knob is turned all the way to the left, the signal will be sent only to the L and odd (ODD) groups A whose assign switches are pressed. If it is turned all the way to the right, the signal will be sent only to the R and even (EVEN) groups. If the knob is set B to the center position, the same amount of signal will be sent to the stereo L and R, and the odd/even groups. AON switch This switch turns the input module on/off. When the switch is pressed in the input module is on. Be sure to turn off input modules that are not in use. Even when a module is off, the SIGNAL and PEAK indicators will light if a signal is being input. You can also use the PFL switch to monitor the signal even if a module is off. BPFL switch C PFL is an acronym for Pre-Fader Listen. This switch allows you to monitor the signal of the input module regardless of the fader position, the settings of the ON switch, the group assign switches, or the AUX settings. As the name suggests, the signal is taken pre-fader (post EQ). You may listen to an individual module, or to two or more modules simultaneously. The PFL indicator located at the top of the STEREO module will light when a PFL switch is on. CFader This adjusts the signal level that is sent to the various outputs. Faders are used individually or in conjunction with the faders of the other input modules to create the desired mix balance. A position at the zero (0) marking is the nominal level. Raising the fader above 0 provides up to 10dB of gain. MX400 User’s Guide Stereo module S T 1 A B +4 -10 PEAK SIGNAL HIGH –15 +15 LOW –15 +15 AUX 2 1–2 3–4 ST AUX 1 BAL/PAN L ODD R EVEN LEVEL 0 10 ON PFL S T 3 +4 -10 PEAK SIGNAL AUX 4 AUX 3 Stereo module S T 1 A B +4 -10 PEAK SIGNAL HIGH –15 +15 LOW –15 +15 AUX 2 1–2 3–4 ST AUX 1 BAL/PAN L ODD R EVEN LEVEL 0 10 ON PFL S T 3 +4 -10 PEAK SIGNAL AUX 4 AUX 3 Stereo module 1A/B switch 1 This switch selects the signal source for the stereo module. 2 Select either ST INPUT A (unbalanced 1/4” phone type) or ST INPUT B (RCA pin) input. This switch is not provided for [ST3] or [ST4]. 3 2Sensitivity select (+4/–10) switch This switch selects the gain appropriate for the input signal level. The sensitivity is –10dB when the switch is pressed in, and +4dB when the switch is not pressed in. 4 3SIGNAL and PEAK indicators When the post EQ signal level (nominal level 0dB) reaches –20dB, the SIGNAL indicator will light. This indicator indicates that a signal is being input. When the post EQ signal level reaches 3dB before clipping level, the PEAK 5 indicator will light. This indicator indicates that the signal has approached clipping level. Set the signal level based on the status of the PEAK indicator. 64EQ controls (HIGH, LOW) This is a 2-band equalizer with center frequencies, range, and type as shown below. HIGH: 12 kHz +/–15dB shelving type 7 LOW: 80 Hz +/–15dB shelving type The frequency response is flat when the knob is in the center position. 85AUX 1 / AUX 2 / AUX 3 / AUX 4 switches These switches send the mono signal to the AUX buses. They are on when pressed in. 9 [ST1] and [ST2] select the AUX 1 and AUX 2 buses. 0 [ST3] and [ST4] select the AUX 3 and AUX 4 buses. 2 6Assign switches (1-2, 3-4, ST) 3 These switches assign the signal of the stereo module to the group outputs and the ST output. The PAN control located below adjusts the stereo position of the signal between the odd (ODD) group and left (L) outputs and the even (EVEN) group and right (R) outputs. 5 7BAL/PAN control The BAL/PAN knob adjusts the balance o...
Este manual também é adequado para os modelos :Instrumentos musicais - MX400-12 (935.13 kb)
Instrumentos musicais - MX400-16 (935.13 kb)
Instrumentos musicais - MX400-8 (935.13 kb)