Assessments - 2, GPA: 4.5
(
)
)
|
por este dispositivo também tem outras instruções :
Facilidade de uso
You should have a large Phillips head (+) screwdriver on hand for assembly. Figure 1 • Check the items that come with the unit to make sure that everything shown in Figure 1 (A through L) is included. All screws are in a plastic bag inside of the packing card- board. x4 x2 Gx1 x14 Hx2 x2 JFIKABCx2 EDLx2 Figure 2 21 • Before starting actual assembly of the stand, undo the clip at location 1 (Figure 2) where the pedal cable comes out the back of crosspiece D. Pull out the coiled cable and refasten two clips at points 1 and 2 as shown in the illustration. 1 Assembling the stand Refer to Figures 3, 4 and 5 as you assemble the stand according to the following procedure. Figure 3 GAHDBGFICFI** EIJI3LLE5Side upright Crosspiece Bottom 4 1.Attach E brackets to side uprights A and B using the I screws (Figure 3). • When attaching the E bracket to the side upright B, slip a J clip onto the I screw before screwing the I screw into the upright at point 3. 2. Attach angle brackets F to side uprights A and B using the four I screws (Figure 3). 3.Install height adjustment screw H into hole 4 located in the center of the back of crosspiece D (Figure 3). 4.Attach side uprights A and B to crosspiece D using the four G screws (Figure 3). • Make sure that crosspiece D is correctly positioned as indicated by 5 in the inset of Figure 3. It should be perpendicular (at a 90-degree angle) to the two side uprights. Also make sure that uprights A and B are parallel with each other. If the pieces are not positioned correctly, the nuts built into crosspiece D will not seat properly with the G screws. This can result in stripping of the threads and free turning of nuts. 427B-E-031A E-27 AP31/33_E_26_30.p65 Page 27 03.10.22, 5:05 PM Adobe PageMaker 6.5J/PPC Figure 4 (Back) CI6JA B J L E 5. Attach back panel C to the E brackets and crosspiece D. Note that the back panel C should be installed so it is in front of the E brackets (Figure 4). Use the two L screws, six I screws to secure the back panel in place (Figures 3 and 4). Note that you must also install the second J clip at this time as shown in the illustration. • First, install the topmost L screws on the left and right sides of the back panel C. Note that you should slip the other J clip onto the I screw at point 6 before you screw the I screw in. • The back panel C should rest on the feet of side uprights A and B as indicated by 7 in the illustration. Press the back panel C against crosspiece D while installing the L screws. L 7 Figure 5 H 6. Rotate height adjustment screw H until it supports crosspiece D, preventing the crosspiece from bending when you press the pedals (Figure 5). IMPORTANT! Be sure to install adjustment screw H and perform the adjustment procedure described above before depressing the pedals. Failure to do so can result in damage to crosspiece D. E-28 AP31/33_E_26_30.p65 Page 28 2 Installing the Keyboard onto the Stand Caution Take care that you do not pinch your fingers be...
Este manual também é adequado para os modelos :Aparelhos de ar condicionado - CELVIANO AP-31 (1.9 mb)
Aparelhos de ar condicionado - CELVIANO AP-31V (1.9 mb)
Aparelhos de ar condicionado - CELVIANO AP-33 (1.9 mb)
Aparelhos de ar condicionado - CELVIANO AP-33V (1.9 mb)