Assessments - 6, GPA: 4.2
(
)
)
|
Facilidade de uso
For information on using Fender® FUSE™, Ableton® Live or Amplitube®, please see the separate manuals for each product available at fender.com/support Navigation There are just a few basics of Bronco 40 navigation that you should know before you explore any further... Selecting Presets The most powerful feature of your Bronco 40 amplifier is its ability to store every amplifier setting and effect selection as a preset that you can instantly recall using the PRESET knob, or remotely from your computer or footswitch. Use the PRESET knob to select one of 24 presets. Presets are stored in three banks, colored AMBER, GREEN and RED. Turn the PRESET knob to scroll through each bank of presets in the following order: Each preset is based on one of the eight amplifier types labeled next to each of the preset LEDs. That gives you a total of three presets for each amplifier type. d The RED and GREEN banks are for creating your own presets. The AMBER bank of presets can only be modified using Fender FUSE software available free at Each preset includes the settings of all the programmable knobs on the Bronco 40, which includes every knob except the MASTER volume and PRESET knobs. Programmable Knobs Because the setting of every knob on the Bronco 40 amplifier (except MASTER) is part of each preset, all programmable knobs are normally inactive and knob positions will NOT show their actual settings when a preset is first selected. How do I activate a programmable knob? The moment you turn any programmable knob it instantly becomes active and it will remain active until you select a different preset, at which time it becomes inactive again. You may hear a big change in volume or tone when you first turn a programmable knob if there happened to be a large difference between the knob's starting position and the stored preset setting. For example, if the VOLUME knob is pointing to "8" but the stored preset VOLUME setting is "2," the volume level will jump from "2" to "8" when you start turning the VOLUME knob because the VOLUME knob is now instantly active at "8." d The only way to know what the preset setting of a knob is before you turn it, is by using Fender FUSE software and connecting the Bronco 40 to your computer. Effects & Compression Use the FX knob to select effects and the COMP knob to select levels of signal compression. The FX and COMP knobs share the same three indicator LEDs. The knob that is being turned or has been turned most recently, has control of these LEDs. PROGRAMMABLE knobs are inactive unless turned Turn a PROGRAMMABLE knob to activate it OFFOFFADBCULTRAMEDHIGHLOW123COMPACTIVE AMBER Bank ( Factory presets ) GREEN Bank ( User presets ) RED Bank ( User presets ) These LEDs are linked to whichever knob was turned last BRONCO™ 40 fender.com 3 The LEDs are numbered 1, 2, 3 and correspond to three positions within each of the 4 selection ranges on each knob. Use the LEDs to determine exactly which position the knob is pointing to, for example, A1, A2 or A3 (A1 is shown below). OFFOFFADBCULTRAMEDHIGHLOW123COMPACTIVE Effects Selections The table below lists the effect selections for the FX knob. EFFECTS A1 Chorus A2 Flanger A3 Phaser B1 Envelope Filter #1 B2 Envelope Filter #2 B3 Octave Down C1 Small Room Reverb C2 Mono Delay C3 Ducking Delay D1 Combo Effect #1 D2 Combo Effect #2 D3 Combo Effect #3 d You can completely change the effects list on your Bronco™ 40 amplifier using Fender® FUSE™ software available at Effects and Channel Volume Levels You can adjust the effects level or channel volume level by holding down the EXIT button while rotating either the GAIN or FX knob. Tap Button The TAP button can be used to tap in delay time and modulation rate settings: • Delay time — TAP button blinks green: • Modulation rate — TAP button blinks red: When you select a delay type effect, the TAP button will blink green in time with the delay time setting. When you select a modulation type effect, the TAP button will blink red in time with the modulation rate setting. To set the TAP interval of effects: 1. Select an effect that causes the TAP button to blink, using the FX knob. 2. Press the TAP button twice rhythmically in time with the desired interval. d Press the TAP button just one time to set the delay or modulation interval to its maximum value. Compression Active The EXIT button will light up when the compression circuit is actively compressing the signal volume level. Higher compression settings limit the dynamic volume range of your bass, effectively reducing distortion and increasing sustain. Experiment to find the right setting that suits your style of playing. XLR Line Output The LINE OUT jack on the rear panel is a balanced, line level output suitable for connection to mixing consoles and recording equipment. This is a mono output, however, the USB audio connection provides a means to record in stereo (see USB Port on page 5). LINE OUT Tuner Button Your ...