Assessments - 4, GPA: 4.5
(
)
)
|
Facilidade de uso
The KXR 200 uses state of the art technology to deliver clear, resonant and most importantly...musical sound. The KXR 200 is actually much more than a keyboard amp. With its heavy-duty Fender® Special Design speaker and dual piezo-electric horn, it could actually be classified as a self-contained, portable P.A. system. The KXR 200 is suitable for almost any musical instrument requiring full-range reinforcement, for example, electronic keyboards, acoustic/electric guitar, electric violin and also vocals. Compact packaging and high output power make the KXR 200 the perfect full-range instrument amplifier for rehearsal, studio or performances. The preamp section of the KXR 200 features four independent channels. Channels one, two, and three each feature a single 1/4 inch, high-impedance-input jack, a three- band equalizer, a channel volume control, an effects send control and a reverb send control. Emphasizing on vocal, channel four is equipped with a low impedance XLR jack in addition to the 1/4 inch jack. Furthermore, channel four also features a four-band equalizer centered around the vocal frequencies, while still covering the whole audible audio spectrum. Channel four is also equipped with a channel volume control, an effects send control and a reverb send control. In addition to the features mentioned above, each channel also possesses an independent effects loop insertion point on the rear panel. This feature makes the KXR 200 even more versatile. The KXR 200 is also equipped with a master section which contains a master volume control, an effect return control, a reverb return control, an effects send jack, an effects return jack, and a line-out portion comprising of a 1/4 inch and XLR jacks. The KXR 200 keyboard amplifier was designed to give years of reliable service under all conditions and is equipped with a unique implementation of our exclusive, defeatable DELTACOMPTM compressor system. When DELTACOMPTM is engaged, it is practically impossible to cause the power amplifier to clip (distort). With DELTACOMPTM, apparent compressor release time is kept short, yet waveform distortion is kept to a minimum at low frequencies. The selection of a Fender® amplifier will reward you with years of quality music in a wide range of sonic possibilities. This manual is designed to familiarize you with the features and functions of your KXR 200 amplifier. Read this manual carefully so you will benefit from these features as soon as you start using your new Fender® amplifier. The built-in quality of a Fender® amplifier is the result of over four decades of dedication in the combined skills of the Fender® design team. That’s why we proudly say, FENDER®... The Sound That Creates Legends. CHANNEL 1 INPUT (1/4 INCH) - Plug-in connector for instruments. This balanced input can handle as much as 8V R.M.S. CHANNEL 1 VOLUME CONTROL - This control adjusts the preamplifier gain of channel 1. It works in conjunction with the Master Volume control ( item I) to set the overall loudness of the amplifier for channel 1 only. Being a true “gain” control, it allows for the use of a variety of microphones, keyboards or other instruments with differing output signal levels. Low-level instruments generally require a higher Channel Volume setting while “hotter” keyboards will require a lower setting. CHANNEL 1 EQUALIZER - This equalizer allows adjustments of the tonal characteristics of channel 1 before amplification. Each control provides a 12dB boost or cut to bands of frequencies centered about 130, 540, and 4200 Hz. Note that all equalizer sections of the KXR 200 are designed so that if all center frequencies are set at +12dB, a flat overall response would be obtained. This is very useful if the signal source is weak. CHANNEL 1 EFFECTS SEND CONTROL - This control works in conjunction with the effects send jack (item R), effects return jack (item S), and the effect return control (item J) to , respectively, allow a desired amount of preamp signal to be massaged, and to control the amount of return signal that has gone through an external effects device. The effects send control in conjunction with the effects send jack could be used to drive another KXR 200 as a slave amp. This is done by connecting the effects send jack, with a standard guitar cord, to the effects return jack of another KXR 200. Note that each channel could be set to send a different amount of signal to the effects bus. CHANNEL 1 REVERB SEND CONTROL - This control works in conjunction with the reverb return control (item K) to allow the amount of reverb to be mixed with the dry signal. The amount of reverb-sent signal is independent for each channel. CHANNEL 2 AND 3 - These two channels are provided for two additional instruments. All the controls and jacks operate in the same manner as those in channel 1. When not in use, it is best to turn the channel volume, the effects send and the reverb send controls all the way down to avoid any amplification of unwanted nois...