Assessments - 4, GPA: 4
(
)
)
|
Facilidade de uso
Each of the GAIN — REVERB knobs will revert to the positions they were to prior to entering the EFFECT mode. * Effect settings will remain in effect even if the AMP SELECT button is pressed to select another amp type. When you recall a different memory number with the “Recall Memory” function (refer to page 10), the settings for that memory number’s effect will then be in affect. With the procedures on this page, you can create an original sound (settings), and along with the reverb and effect settings they can be stored in the DG amplifier’s internal memory for instant recall at any- time.The procedure for storing data in memory is explained on the next page. DG100-212A/DG80-210A/DG80-112A/DG130HA DG100-212A/DG80-210A/DG80-112A/DG130HA e Preset setting data, specially created by Yamaha for the DG Series Amplifiers, is installed in memory numbers 1-80 when the amplifier is shipped from the factory. (Refer to the “Patch List” on page 83.) Setting data contains Amp Type and its settings (GAIN, MASTER, Tone Control, Reverb, Tremolo, Chorus and Tape Echo) that you can recall freely and use at any time. Motor drives in the knobs will automatically set the knobs to the corresponding positions. Also, any settings that you create can be saved (store) to any of the memory numbers 1 – 128. After creating a favorite sound, try saving it. ¦ Recall Memory (Recall) Sound settings stored in memory can easily be recalled by selecting a memory number. When a memory is recalled, the current settings will be changed. If you want to keep the settings, use the Store operation, described on the right side of this page, to store settings to memory. 1. Press the button, the AMP or EFFECT mode display will light. 2. Use the / buttons to select the memory number you want to recall. The memory number will appear on the display (flashing). 3. Press the button. The flashing memory number will light. Each of the knobs, and the Amp Select Display will change according to the data recalled from memory. * Settings will not change until the button is pushed. * TRIM and OUTPUT knob settings will not change with the Recall operation. * It takes anywhere from 1 – 10 seconds for the knobs to change to their set positions however, internal settings (sound) will change instantly. *“E1” will appear on the display if the volume knob does not go to its assigned position, or the device does not recognize the recall command after 20 seconds has elapsed from the start of the recall operation. Continued use of the device in this condition may result in fire or electrical shock. Take the unit to the music dealer where you purchased it, or to the nearest Yamaha Service Center for repair. The memory number to be recalled, shown on the display, goes from flashing to lit. Execute RecallLights Select the memory number to be recalled. A MIDI foot controller or other external MIDI device can be used to select and recall memory. Refer to the following page to page 13 for details. Initialize the memory While holding both the button and button, turn the Power Switch ON, the initialize to factory preset operation will be carried out and the entire memory will be returned to its factory preset condition. When the initialize operation is carried out, data in memory numbers 1-80 will be re-written with data in the Patch List and the data in memory numbers 81 – 128 will also be reset to their factory preset condition. Any data you have saved to memory will be erased, so we strongly recommend that you save any important data to an external MIDI device or document the settings before carrying out the operation. Store Settings 1. Use the procedure on page 9 and create a sound using the eight preset amp types and control knobs on the front panel. * Each of the Utility Mode’s settings cannot be stored in individual memory. When the power is switched OFF, each memory’s settings are stored in memory as common settings. When the power is turned ON, those settings are recalled. 2. Press the button, the AMP or EFFECT mode display lamp will light. 3. Using the / buttons, select a memory number to which the settings will be saved.The memory number will flash in the display. * Press and hold either of the / buttons makes memory numbers cycle rapidly. * The third digit of the memory number (100 – 128) is represented by a dot between the two digits. Example) 128 is displayed as > 4. Press and hold the button for about one second, until “8.8” appears on the display. Release the button, the flashing memory number will then light indicating the setting is saved to memory. * TRIM and OUTPUT settings cannot be stored in memory. Use the MASTER knob to set backing and soloing levels. The memory number to be stored. Flashing > 8.8. > Lights Execute Store Select the memory number. Lights Data stored in memory (1 – 128) can be saved to an external MIDI storage device. Refer to page 12 for details. HINT Some hints on storing memory numbers When storing data to memory numbers, divide the memory...