Assessments - 4, GPA: 3.3
(
)
)
|
Facilidade de uso
It will boost or cut by 14 dB at 60 Hz. 6. Lo-Mid: This control adds thickness and body to your tone. It will boost or cut by 12 dB at 340 Hz. 7. Hi-Mid: This control adds punch to your overall tone. It will boost or cut by 10 dB at 2 kHz. 8. Treble: Increasing this control will add presence and attack to your bass tone. It will boost or cut by 15 dB at 10 kHz, perfect for enhancing “slap” and pick playing. 9. Aux In: This is a 3-conductor, 1/8-inch, stereo jack that allows playback from a Compact Disc, MP3 player or other audio device. The overall volume level will be determined by the audio device, so start with lower volume levels and increase as needed. 10. Headphones: This is a 3-conductor, 1/8-inch input jack intended for headphone use. The amplifier’s internal speaker is disconnected when this jack is used. 11. Power Switch: This dual-function component is both an On/Off power switch and a status indicator light. When illuminated, it shows that your amplifier is ready to be played. To turn amplifier on, press switch upward. To turn amp off, press switch downward. kustom.com KXB100 Back Panel KXB100 Power Cord: This supplies AC power to the amplifier. If the cord becomes damaged, take the amplifier to an authorized service center for repair. External Speaker: This is a two-conductor, .-inch external speaker jack. (Note: This jack is wired in series with the amp’s internal speaker. Therefore, the internal speaker still functions when an external speaker cabinet is added. For this reason, there is no minimum external speaker impedance load.) Effects Loop Send: Use this 2-conductor, .-inch jack to connect to the input of an external effects processor or equalizer. This jack can also be used as a Preamp Out. Effects Loop Return: Use this 2-conductor, .-inch jack to connect to the output of an external effects processor or equalizer. This jack can also be used as a Power Amp In. Balanced Line Out: This XLR jack is used to connect the amplifier to a mixer or other line level amplifier. (Note: This output is post-EQ and post- Effects Loop but is located before the Volume control.) Direct Out Volume: This control sets the output level for the Balanced Line Out. Set in its lower ranges until necessary volume has been determined. Ground Lift: Activating this switch removes the ground connection on the Balanced Line Out jack. If necessary, use this switch to eliminate hum. kustom.com KXB100 Suggested Settings The following suggested settings will help you dial in a variety of popular tones. Keep in mind, these are starting points to get you up and running with your KXB amplifier. Feel free to experiment to achieve your own signature sounds. KXB100 TRADITIONAL/VERSATILE TONE In this setting, the amplifier will deliver a traditional, yet versatile, electric bass sound. Whether you are playing Rock, Country, Blues or Gospel, this setting will get you close. If you play with a pick and want less treble attack on the notes, decrease the amount of high frequencies using the Treble control. If you need a deeper bottom end, increase the amount of low frequencies using the Bass control. Adjust the amount of Midrange to best match the tone of your bass guitar and how it fits into the overall sound. KXB100 FUNKY, SLAPPED TONES This style of music needs a strong attack with lots of treble. Using less Midrange will produce the extra top end neces sary for this type of music. If you use a “slapping” thumb technique, add a bit more low end and extra volume – or less if you really hit the strings hard. KXB100 ALTERNATIVE STYLE These settings are designed for upper-end punch and edge that will cut through most any sound mix. This tone will work well with pick or fingers. Make sure your bass guitar’s volume control is turned up all the way. Since you’re adding volume, be careful with the amount of Bass, Mid and Treble that you dial in, as it can also add some distortion to the sound. kustom.com Kustom® KXB100 Specifications Output Power 100 Watts 4 Ohms at 10% THD+N Speaker 1 X 15” Custom Designed 4 Ohms Input Impedance Dual Input 0 dB: 500K ohm, -6dB: 95K Ohm Gain 72 dB Gain and Master at Max, All EQ at 12 o’clock S/N Ratio -80 dB typical Below rated power DIrect Output Electronically Balanced XLR Ground Lift Switch and Level control Aux Input 1.2 V Sensitivity Stereo 3.5mm High Impedance Headphone Output 15 mW @ 30 ohms per channel Stereo 3.5mm, 8 ohm minimum Effects Loop 900 mV/1K Ohm output Impedance Effects Send, Gain @ 12 o’clock, Master fully CW 900mV/22K Ohm input Impedance Effects Return, Gain @ 12 o’clock, Master fully CW Amplifier Tone Controls 60 Hz +/- 15 dB 500 Hz +/- 10 dB 2 KHz +/- 10 dB 10 KHz +/- 15 dB Power Requirements USA/Canada 120VAC/60Hz, 180W Europe 230VAC/50Hz, 180W UK 240VAC/50Hz, 180W Australia 240VAC/50Hz, 180W Japan 100VAC/50-60Hz, 180W Dimensions/Weight cm3/Kilogram 59.7 (Height) X 47.6 (Width) X 38.1 (Depth), 24 Kilogram Inches/Pounds 23.5 (Height) X 18.75 (Width) X 15.0 (Depth), 53 Lbs kustom.com ...