Assessments - 5, GPA: 3.6
(
)
)
|
Facilidade de uso
Due to physical specifications, a great piece for mobile DJ’s, roller rinks, small clubs, When used in multiples of two that rivals that of units that can cost The DJ Scan/RG™ was designed to run in with any universal DMX-512 controller. Customer Support: American DJ ® provides a toll free customer support line, to provide set-up and installation help question should you encounter problems during operation. You may also visit us on the web at for any comments or suggestions. Toll free customer service hours are Monday through Friday 9:00 a.m. to 5:30 p.m. Pacifi c Standard Time. Voice: (800) 322-6337 Fax: (323) 582-2610 E-mail: support@americandj.com Warning! To prevent or reduce the risk of electrical shock or fire, do not expose this unit to rain or moisture. Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs yourself, doing so will void your manufactures warranty. In the unlikely event your unit may require service please contact American DJ ® customer support. Do not discard the shipping carton in the trash. Please recycle when ever possible. Improvements and changes in specifications and design to this manual and unit may be made at any time without prior notice. HALOGEN LAMP WARNING! This fixture is fitted with a halogen lamp which is highly susceptible to damage if improperly handled. Never touch the lamp with your bare fingers as the oil from your hands will shorten the lamp life. Never install, mount, or place this fixture in areas prone to heavy vibration. Also, never move the fixture until the lamp has had ample time to cool. Remember, lamps are not covered under warranty conditions. © American DJ Supply ® - - DJ Scan/RG™ Instruction Manual Page 2 DJ Scan/Quick Start DJ Scan/RGSafety DJ Scan/Quick Start DJ Scan/RGSafety • Do not spill water into or on to your • Be sure that the local for your unit. • Do not attempt to operate or broken. Please route your • Do not attempt to remove or the ground prong from the electrical cord. This prong is used to reduce the shock and fire in case of an internal short. • Disconnect from main power before making any • Do not remove the top cover under any There are no user serviceable parts inside. • Never plug this unit in to a dimmer pack • Always be sure to mount this unit in an area that ventilation. Allow about 6” (15cm) between this device and a wall. • Do not attempt to operate this unit, if it becomes damaged in any way. • Never operate this unit when it’s cover is removed. • To reduce the risk of electrical shock or fire, do not expose this unit rain or moisture • This unit is intended for indoor use only, use of this product outdoors voids all warranties. • During long periods of non-use, disconnect the unit’s main power. • Always mount this unit in safe and stable matter. • Power Cord Protection - Power cords should be routed so they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the unit. • Cleaning -The fixture should be cleaned only as recommended by the manufacturer. • Heat -The unit should be situated away from heat sources such as radiators, heat registers, stoves, or other appliances (including amplifiers) that produce heat. • The fixture should be serviced by qualified service personnel when: A. The power-supply cord or the plug has been damaged. B. Objects have fallen, or liquid has been spilled into the appliance. C. The appliance has been exposed to rain or water. D. The fixture does not appear to operate normally or exhibits a marked change in performance. © American DJ Supply ® - - DJ Scan/RG™ Instruction Manual Page 3 Master/Slave Quick Alone Mode Connect up to four units together via XLR cables. The master unit will run the slaves to the masters built in programs and internal microphone. Plug in all on, it will run through an internal their zero position. After the self test the units will chase to the several built in programs. DJ Scan/RG™ Features The DJ Scan/RG™ features a bright 150 watt/500 hour lamp life halogen bulb with a separate gobo and color The color wheel features seven brilliant colors plus white and the 6 gobos plus a large and small spot. This fixture incorporates the use of high quality stepper motors for a more accurate mirror Mirror movement allows for a full 90 degree tilt (vertical) and a 45 degree pan (horizontal). An internal built in microphone allows the fixtures to run in Stand Alone mode so there is no need for an external controller. The DJ Scan/RG™ may also be set-up to run in a Master-Slave mode when used in multiples, up to four units. When used Master-Slave mode, the unit will chase to several internal programs. The DJ Scan/RG™ can also be controlled via a standard DMX controller such as the American DJ ® Show Designer, ™ or the American DJ ® DMX Operator,™ giving the user i...